p87lpc762fd NXP Semiconductors, p87lpc762fd Datasheet - Page 4

• Manufacturer Part Number: p87lpc762fd
• Description: Low Power, Low Price, Low Pin Count 20 Pin Microcontroller With 2 Kbyte Otp
• Manufacturer: NXP Semiconductors

Philips Semiconductors
GENERAL DESCRIPTION
The 87LPC762 is a 20-pin single-chip microcontroller designed for
low pin count applications demanding high-integration, low cost
solutions over a wide range of performance requirements. A
member of the Philips low pin count family, the 87LPC762 offers
programmable oscillator configurations for high and low speed
crystals or RC operation, wide operating voltage range,
programmable port output configurations, selectable Schmitt trigger
inputs, LED drive outputs, and a built-in watchdog timer. The
87LPC762 is based on an accelerated 80C51 processor
architecture that executes instructions at twice the rate of standard
80C51 devices.
FEATURES
ORDERING INFORMATION
2001 Oct 26
An accelerated 80C51 CPU provides instruction cycle times of
300–600ns for all instructions except multiply and divide when
executing at 20 MHz. Execution at up to 20 MHz when
V
2.7 V to 6.0 V operating range for digital functions.
2 kbytes EPROM code memory.
128 byte RAM data memory.
32-byte customer code EPROM allows serialization of devices,
storage of setup parameters, etc.
Two 16-bit counter/timers. Each timer may be configured to toggle
a port output upon timer overflow.
Two analog comparators.
Full duplex UART.
I
Low power, low price, low pin count (20 pin)
microcontroller with 2 kbyte OTP
2
DD
C communication port.
= 4.5 V to 6.0 V, 10 MHz when V
P87LPC762BDH
P87LPC762BN
P87LPC762BD
P87LPC762FN
P87LPC762FD
Part Number
0 to +70, Plastic Thin Small Outline Package
–45 to +85, Plastic Small Outline Package
–45 to +85, Plastic Dual In-Line Package
0 to +70, Plastic Small Outline Package
Temperature Range C and Package
0 to +70, Plastic Dual In-Line Package
DD
= 2.7 V to 6.0 V.
1
Eight keypad interrupt inputs, plus two additional external interrupt
inputs.
Four interrupt priority levels.
Watchdog timer with separate on-chip oscillator, requiring no
external components. The watchdog timeout time is selectable
from 8 values.
Active low reset. On-chip power-on reset allows operation with no
external reset components.
Low voltage reset. One of two preset low voltage levels may be
selected to allow a graceful system shutdown when power fails.
May optionally be configured as an interrupt.
Oscillator Fail Detect. The watchdog timer has a separate fully
on-chip oscillator, allowing it to perform an oscillator fail detect
function.
Configurable on-chip oscillator with frequency range and RC
oscillator options (selected by user programmed EPROM bits).
The RC oscillator option allows operation with no external
oscillator components.
Programmable port output configuration options:
quasi-bidirectional, open drain, push-pull, input-only.
Selectable Schmitt trigger port inputs.
LED drive capability (20 mA) on all port pins.
Controlled slew rate port outputs to reduce EMI. Outputs have
approximately 10 ns minimum ramp times.
15 I/O pins minimum. Up to 18 I/O pins using on-chip oscillator
and reset options.
Only power and ground connections are required to operate the
87LPC762 when fully on-chip oscillator and reset options are
selected.
Serial EPROM programming allows simple in-circuit production
coding. Two EPROM security bits prevent reading of sensitive
application programs.
Idle and Power Down reduced power modes. Improved wakeup
from Power Down mode (a low interrupt input starts execution).
Typical Power Down current is 1 A.
20-pin DIP, SO, and TSSOP packages.
20 MHz (5 V), 10 MHz (3 V)
20 MHz (5 V), 10 MHz (3 V)
20 MHz (5 V), 10 MHz (3 V)
20 MHz (5 V), 10 MHz (3 V)
20 MHz (5 V), 10 MHz (3 V)
Frequency
Drawing Number
87LPC762
SOT146–1
SOT163–1
SOT146–1
SOT163–1
SOT360–1
Preliminary data