s5935qrc Applied Micro Circuits Corporation (AMCC), s5935qrc Datasheet - Page 27

• Manufacturer Part Number: s5935qrc
• Description: Pci Product
• Manufacturer: Applied Micro Circuits Corporation (AMCC)

S5935 – PCI Product
NON-VOLATILE MEMORY INTERFACE
SIGNALS
This signal grouping provides for connection to exter-
nal non-volatile memories. Either a serial or byte-wide
device may be used.
The serial interface shares the read and write control
pins used for interfacing with byte-wide memory
devices. Since it is intended that only one (serial or
byte wide) configuration be used in any given imple-
mentation, separate descriptions are provided for
Serial nv Devices
Note: SCL and SDA are not controlled by FLT#.
Byte-Wide nv Devices
AMCC Confidential and Proprietary
Signal
EA[15:00]
SCL
SDA
SNV
EQ[7:0]
Signal
EWR#
ERD#
Type
t/s
t/s
in
Type
out
t/s
t/s
t/s
Serial Clock. This output is intended to drive a two-wire Serial Interface and functions as the bus’s master.
It is intended that this signal be directly connected to one or more inexpensive serial non-volatile RAMs or
EEPROMs. This pin is shared with the byte wide interface signal, ERD#.
Serial Data/Address. This bidirectional pin is used to transfer addresses and data to or from a serial
nvRAM or EEPROM. It is an open drain output and intended to be wire-ORed with all other devices on the
serial bus using a 4.7K external pull-up resistor. This pin is shared with the byte wide interface signal,
EWR#.
Serial Non-Volatile Device. This input, when high, indicates a serial boot device or no boot device is
present. When this pin is low, a byte-wide boot device is present.
External nv memory address. These signals connect directly to the external BIOS (or EEPROM) or
EPROM address pins EA0 through EA15. The PCI interface controller assembles 32-bit-wide accesses
through multiple read cycles of the 8-bit device. The address space from 0040h through 007Fh is used
to preload and initialize the PCI configuration registers. Should an external nv memory be used, the
minimum size required is 128 bytes and the maximum is 64K bytes. When a serial memory is con-
nected to the S5935, the pins EA[7:0] are reconfigured to become a hardware Add-On to PCI mailbox
register with the EA8 pin as the mailbox load clock. Also, the EA15 signal pin will provide an indication
that the PCI to Add-On FIFO is full (FRF#), and the EA14 signal pin will indicate whether the Add-On to
PCI FIFO is empty (FWE#).
External nv memory read control. This pin is asserted during read operations involving the external
non-volatile memory. Data is transferred into the S5935 during the low to high transition of ERD#. This
pin is shared with the serial external memory interface signal, SCL.
External nv memory write control. This pin is asserted during write operations involving the external
non-volatile memory. Data is presented on pins EQ[7:0] along with its address on pins EA[15:0]
throughout the entire assertion of EWR#. This pin is shared with the serial external memory interface
signal, SDA.
External memory data bus. These pins are used to directly connect with the data pins of an external
non-volatile memory. When a serial memory is connected to the S5935, the pins EQ4, EQ5, EQ6 and
EQ7 become reconfigured to provide signal pins for bus mastering control from the Add-On interface.
each. The S5935 provides the pins necessary to inter-
face to a byte wide non-volatile memory. When they
are connected to a properly configured serial memory,
these byte wide interface pins assume alternate func-
tions. These alternate functions include added
external FIFO status flags, FIFO reset control, Add-On
control for bus mastering and a hardware interface
mailbox port.
Description
Description
Revision 1.02 – June 27, 2006
Data Book
DS1527
27