24C01C-I/SN Microchip Technology, 24C01C-I/SN Datasheet - Page 5

• Manufacturer Part Number: 24C01C-I/SN
• Description: IC EEPROM 1KBIT 400KHZ 8SOIC
• Manufacturer: Microchip Technology

Specifications of 24C01C-I/SN

• Memory Size: 1K (128 x 8)
• Package / Case: 8-SOIC (3.9mm Width)
• Operating Temperature: -40°C ~ 85°C
• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Speed: 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 4.5 V ~ 5.5 V
• Organization: 128 K x 8
• Interface Type: I2C
• Maximum Clock Frequency: 0.4 MHz
• Access Time: 1 ms
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Maximum Operating Current: 3 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 4.5 V, 5.5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

2.0
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
2.1
This is a bidirectional pin used to transfer addresses
and data into and data out of the device. It is an open
drain terminal; therefore, the SDA bus requires a pull-
up resistor to V
400 kHz).
For normal data transfer SDA is allowed to change only
during SCL low. Changes during SCL high are
reserved for indicating the Start and Stop conditions.
2.2
This input is used to synchronize the data transfer from
and to the device.
2.3
The levels on these inputs are compared with the
corresponding bits in the slave address. The chip is
selected if the compare is true.
Up to eight 24C01C devices may be connected to the
same bus by using different Chip Select bit combina-
tions. These inputs must be connected to either V
V
2.4
This pin is utilized for testing purposes only. It may be
tied high, tied low or left floating.
2.5
The 24C01C employs a V
which disables the internal erase/write logic if the V
is below 3.8 volts at nominal conditions.
The SCL and SDA inputs have Schmitt Trigger and
filter circuits which suppress noise spikes to assure
proper device operation even on a noisy bus.
© 2008 Microchip Technology Inc.
A0
A1
A2
V
SDA
SCL
Test
V
SS
SS
CC
.
Name
PIN DESCRIPTIONS
SDA Serial Data
SCL Serial Clock
A0, A1, A2
Test
Noise Protection
CC
PIN FUNCTION TABLE
8-pin
PDIP
(typical 10 kΩ for 100 kHz, 2 kΩ for
1
2
3
4
5
6
7
8
CC
threshold detector circuit
8-pin
SOIC
1
2
3
4
5
6
7
8
TSSOP
8-pin
1
2
3
4
5
6
7
8
CC
CC
or
MSOP
8-pin
1
2
3
4
5
6
7
8
DFN/TDFN
8-pin
1
2
3
4
5
6
7
8
Chip Select
Chip Select
Chip Select
Ground
Serial Data
Serial Clock
Test
+4.5V to 5.5V Power Supply
Function
24C01C
DS21201J-page 5