24LCS22A-I/SN Microchip Technology, 24LCS22A-I/SN Datasheet - Page 14

• Manufacturer Part Number: 24LCS22A-I/SN
• Description: IC EEPROM 2KBIT 400KHZ 8SOIC
• Manufacturer: Microchip Technology

Specifications of 24LCS22A-I/SN

• Memory Size: 2K (256 x 8)
• Package / Case: 8-SOIC (3.9mm Width)
• Operating Temperature: -40°C ~ 85°C
• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Speed: 100kHz, 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.5 V ~ 5.5 V
• Organization: 256 K x 8
• Interface Type: I2C
• Maximum Clock Frequency: 0.1 MHz
• Access Time: 3500 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.5 V
• Maximum Operating Current: 3 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 2.5 V, 5.5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 24LCS22A-I/SNG; 24LCS22A-I/SNG; 24LCS22AI/SN

24LCS22A
8.0
The descriptions of the pins are listed in Table 8-1.
TABLE 8-1:
8.1
This pin is used for flexible write protection of the
24LCS22A. When memory location 7Fh is written with
any data, this pin is enabled and determines the write
capability of the 24LCS22A (Table 6-1).
8.2
This pin is used to transfer addresses and data into and
out of the device, when the device is in the Bidirectional
mode. In the Transmit-Only mode, which only allows
data to be read from the device, data is also transferred
on the SDA pin. This pin is an open drain terminal,
therefore the SDA bus requires a pull-up resistor to
V
For normal data transfer in the Bidirectional mode, SDA
is allowed to change only during SCL low. Changes
during SCL high are reserved for indicating the Start
and Stop conditions.
DS21682E-page 14
CC
(typical 10 kΩ for 100 kHz, 2 kΩ for 400 kHz).
Name
VCLK
SDA
SCL
V
V
WP
NC
CC
SS
PIN DESCRIPTIONS
Write-Protect (WP)
Serial Address/Data Input/Output
(SDA)
PIN FUNCTION TABLE
Write-Protect (active low)
Ground
Serial Address/Data I/O
Serial Clock (Bidirectional mode)
Serial Clock (Transmit-Only mode)
+2.5V to 5.5V Power Supply
No Internal Connection
Function
8.3
This pin is the clock input for the Bidirectional mode,
and is used to synchronize data transfer to and from the
device. It is also used as the signaling input to switch
the device from the Transmit-Only mode to the
Bidirectional mode. It must remain high for the chip to
continue operation in the Transmit-Only mode.
8.4
This pin is the clock input for the Transmit-Only mode
(DDC1). In the Transmit-Only mode, each bit is clocked
out on the rising edge of this signal. In the Bidirectional
mode, a high logic level is required on this pin to enable
write capability.
Serial Clock (SCL)
Serial Clock (VCLK)
© 2009 Microchip Technology Inc.