LNK403EG Power Integrations, LNK403EG Datasheet - Page 3

• Manufacturer Part Number: LNK403EG
• Description: IC LED DVR TRIAC 12W DIM SIP-7C
• Manufacturer: Power Integrations
• Series: LinkSwitch®-PHr

Specifications of LNK403EG

• Constant Current: Yes
• Topology: PWM
• Number Of Outputs: 1
• Internal Driver: Yes
• Type - Primary: *
• Type - Secondary: *
• Frequency: 62kHz ~ 70kHz
• Voltage - Supply: 90 V ~ 265 V
• Voltage - Output: *
• Mounting Type: Through Hole
• Package / Case: 7-SIP, 6 Leads, Exposed Pad, Formed Leads
• Operating Temperature: -40°C ~ 150°C
• Current - Output / Channel: *
• Internal Switch(s): Yes
• Efficiency: 85%
• Operating Supply Voltage: 36 V
• Maximum Supply Current: 2.25 mA
• Maximum Power Dissipation: 12 W
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 20 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 596-1300-5

Functional Description
A LinkSwitch-PH device monolithically integrates a controller and
high-voltage power MOSFET into one package. The controller
implements both high power factor and a constant current
output in a single stage. The LinkSwitch-PH controller consists
of an oscillator, feedback (sense and logic) circuit, 5.9 V regulator,
hysteretic over-temperature protection, frequency jittering,
cycle-by-cycle current limit, auto-restart, inductance correction,
power factor and constant current control.
FEEDBACK Pin Current Control Characteristics
The figure shown below illustrates the operating boundaries of
the FEEDBACK pin current. Above I
and below I
Figure 4.
The FEEDBACK pin current is also used to clamp the maximum
duty cycle to limit the available output power for overload and
open-loop conditions. This duty cycle reduction characteristic
also promotes a monotonic output current start-up
characteristic to prevent over-shoot.
REFERENCE Pin
The REFERENCE pin is tied to ground (SOURCE) via an
external resistor. The value selected sets the internal
references, determining the operating mode for dimming
(LNK403-409) and non-dimming (LNK413-419) operation and
www.powerint.com
I
FB(DCMAXR)
I
FB(SKIP)
I
FB(AR)
FEEDBACK Pin Current Characteristic.
I
FB
FB(AR)
the device enters into auto-restart.
Soft-Start and
CC Fold-Back
Region
DC10
Maximum Duty Cycle
CC Control
Auto-Restart
Skip-Cycle
Region
FB(SKIP)
switching is disabled
DC
PI-5433-060410
MAX
the line undervoltage and overvoltage thresholds of the
VOLTAGE MONITOR pin. For non-dimming or PWM dimming
applications with LNK413-419, the external resistor should be a
24.9 kW ±1%, for high line and universal input voltage designs,
and 49.9 kW ±1% for low line input voltage designs. For phase
angle AC dimming with LNK403-409, the external resistor
should be a 49.9 kW ±1%. One percent resistors are
recommended as the resistor tolerance directly affects the
output tolerance.
BYPASS Pin Capacitor Power Gain Selection
LinkSwitch-PH devices have the capability to tailor the internal
gain to either full or a reduced output power setting. This allows
selection of a larger device to minimize dissipation for both
thermal and efficiency reasons. The power gain is selected with
the value of the BYPASS pin capacitor. The full power setting is
selected with a 100 mF capacitor and the reduced power setting
(for higher efficiency) is selected with a 10 mF capacitor. The
BYPASS pin capacitor sets both the internal power gain as well
as the over-current protection (OCP) threshold. Unlike the
larger devices, the LNK4x3 power gain is not programmable.
Use a 10 mF capacitor for the LNK4x3.
Switching Frequency
The switching frequency is 66 kHz. To further reduce the EMI
level, the switching frequency is jittered (frequency modulated)
by approximately ±1 kHz.
Soft-Start
The controller includes a soft-start timing feature which inhibits
the auto-restart protection feature for the soft-start period (t
to distinguish start-up into a fault (short-circuit) from a large
output capacitor. At start-up the LinkSwitch-PH clamps the
maximum duty cycle to reduce the output power. The total
soft-start period is t
Remote ON/OFF and Eco-Smart
The VOLTAGE MONITOR pin has a 1 V threshold comparator
connected at its input. This voltage threshold is used for
remote ON/OFF control. When a signal is received at the
VOLTAGE MONITOR pin to disable the output (VOLTAGE
MONITOR pin tied to ground through an optocoupler photo-
transistor) the LinkSwitch-PH will complete its current switching
cycle before the internal power MOSFET is forced off.
The remote ON/OFF feature can also be used as an eco-mode
or power switch to turn off the LinkSwitch-PH and keep it in a
very low power consumption state for indefinite long periods.
When the LinkSwitch-PH is remotely turned on after entering
this mode, it will initiate a normal start-up sequence with
soft-start the next time the BYPASS pin reaches 5.9 V. In the
worst case, the delay from remote on to start-up can be equal
to the full discharge/charge cycle time of the BYPASS pin. This
reduced consumption remote off mode can eliminate expensive
and unreliable in-line mechanical switches.
SOFT
.
LNK403-409EG/413-419EG
Rev. B 11/10
SOFT
3
)