E-L6386D013TR STMicroelectronics, E-L6386D013TR Datasheet
E-L6386D013TR
Specifications of E-L6386D013TR
Available stocks
Related parts for E-L6386D013TR
E-L6386D013TR Summary of contents
Page 1
... HIN LIN SGND 7 July 1999 L6386D pendent referenced Channel Power MOS or IGBT. The Upper (Floating) Section is enabled to work with voltage Rail up to 600V. The Logic In- puts are CMOS/TTL compatible for ease of inter- facing with controlling devices. UV DETECTION LEVEL SHIFTER LOGIC LVG ...
Page 2
... Bootstrapped Supply Voltage (*) The circuit guarantees 0.3V maximum on the pin (@ Isink = 10mA), with VCC >3V. This allows to omit the "bleeder" resistor connected between the gate and the source of the external MOSFET normally used to hold the pin low; the gate driver assures low impedance also in SD condition ...
Page 3
... Floating Supply Voltage Vout fsw Switching Frequency Vcc 4 Supply Voltage T Junction Temperature j Note 1: if the condition Vboot - Vout < 18V is guaranteed, Vout can range from -3 to 580V. ELECTRICAL CHARACTERISTICS AC Operation (Vcc = 15V 25°C) Symbol Pin Parameter ton 1.3 High/Low Side Driver Turn- ...
Page 4
... Open Drain Low Level Output Voltage, Iod = -2.5mA Vref Comparator Reference voltage Figure 1. Timing Waveforms HIN LIN SD HOUT LOUT V REF V CIN DIAG Note: SD active condition is latched until next negative IN edge. Figure 2. Typical Rise and Fall Times vs. Load Capacitance time (nsec) 250 200 150 100 For both high and low side buffers @25˚ ...
Page 5
... V gate gate 3nF. With C = 100nF the drop would be BOOT 300mV. If HVG has to be supplied for a long time, the C selection has to take into account also the BOOT leakage losses. e.g.: HVG steady state consumption is lower than 200 HVG T is 5ms Figure 4 ...
Page 6
... L6386 Figure 5. Turn On Time vs. Temperature 250 200 150 Typ. 100 50 0 -45 - (°C) Figure 6. Turn Off Time vs. Temperature 250 200 150 Typ. 100 50 0 -45 - (°C) Figure 7. Shutdown Time vs. Temperature 250 200 150 Typ. 100 50 0 -45 - (°C) 6/10 Figure Vcc = 15V 100 125 -45 Figure 9 ...
Page 7
... Figure 11. Vcc UV Turn On Threshold vs. Tem- perature Typ -45 - (°C) Figure 12. Vcc UV Turn Off Threshold vs. Temperature Typ -45 - (°C) Figure 13. Vcc UV Hysteresis vs. Tempera- ture 3 2.5 Typ. 2 1.5 1 -45 - (°C) Figure 14. Output Source Current vs. Tem- 1000 800 600 Typ. 400 200 0 75 100 125 -45 Figure 15. Output Sink Current vs. Tempera- ...
Page 8
... DIM. MIN. TYP. MAX. MIN. a1 0.51 0.020 B 1.39 1.65 0.055 b 0 8.5 e 2.54 e3 15.24 F 7.1 I 5.1 L 3.3 Z 1.27 2.54 0.050 8/10 inch MECHANICAL DATA TYP. MAX. 0.065 0.020 0.010 0.787 0.335 0.100 0.600 0.280 0.201 0.130 0.100 OUTLINE AND DIP14 ...
Page 9
... G 4.6 5.3 0.181 L 0.4 1.27 0.016 M 0.68 S 8˚ (max.) (1) D and F do not include mold flash or protrusions. Mold flash or potrusions shall not exceed 0.15mm (.006inch). inch TYP.. MAX.. MECHANICAL DATA 0.069 0.009 0.063 0.018 0.010 0.020 0.344 0.244 0.050 ...
Page 10
... STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics © 1999 STMicroelectronics – Printed in Italy – All Rights Reserved Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. 10/10 STMicroelectronics GROUP OF COMPANIES http://www ...