VN610SP13TR STMicroelectronics, VN610SP13TR Datasheet
VN610SP13TR
Specifications of VN610SP13TR
Available stocks
Related parts for VN610SP13TR
VN610SP13TR Summary of contents
Page 1
... Active current limitation combined with thermal shutdown and automatic restart protect the device against over-load. Device automatically turns off in case of ground pin disconnection. Tube VN610SP Doc ID 6236 Rev 4 VN610SP 10 1 PowerSO-10 pin voltage clamp protects the device CC Order codes Tape and reel VN610SP13TR 1/26 www.st.com 1 ...
Page 2
Contents Contents 1 Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Electrical specifications ...
Page 3
VN610SP List of tables Table 1. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
List of figures List of figures Figure 1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 5
VN610SP 1 Block diagram and pin description Figure 1. Block diagram GND INPUT Figure 2. Configuration diagram (top view) GROUND INPUT C. SENSE N.C. N.C. Table 2. Suggested connections for unused and not connected pins Connection / pin Floating To ...
Page 6
... These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality document. Table 3. ...
Page 7
VN610SP Table 3. Absolute maximum ratings (continued) Symbol Maximum switching energy E MAX (L = 0.05mH Power dissipation at T tot T Junction operating temperature j T Case operating temperature c T Storage temperature STG 2.2 Thermal data ...
Page 8
Electrical specifications Table 5. Power (continued) Symbol Parameter I Off-state output current L(off2) I Off-state output current L(off3) I Off-state output current L(off4 and V are correlated. Typical difference is 5V. clamp OV Table 6. Protections Symbol I ...
Page 9
VN610SP Table 8. Current sense (9V Symbol Parameter OUT Current sense ratio drift OUT Current sense ratio drift OUT Current ...
Page 10
Electrical specifications Table 9. Logic inputs Symbol V Input low level voltage IL I Low level input current IL V Input high level voltage IH I High level input current IH V Input hysteresis voltage I(hyst) V Input clamp voltage ...
Page 11
VN610SP Table 12. Electrical transient requirements ISO T/R 7637/1 Test pulse 26.5V 1. All functions of the device are performed as designed after exposure to disturbance. 2. One or more functions of the ...
Page 12
Electrical specifications Figure 5. I OUT I /I OUT SENSE 6500 6000 5500 5000 4500 4000 3500 3000 0 12/26 /I versus I SENSE OUT max.Tj=25...150°C min.Tj=25...150° (A) OUT Doc ID 6236 Rev 4 max.Tj=-40°C typical ...
Page 13
VN610SP Figure 6. Waveforms INPUT LOAD CURRENT SENSE CURRENT V CC INPUT LOAD CURRENT SENSE CURRENT V CC INPUT LOAD CURRENT SENSE INPUT LOAD CURRENT LOAD VOLTAGE SENSE CURRENT INPUT LOAD VOLTAGE LOAD CURRENT SENSE CURRENT T j INPUT LOAD ...
Page 14
Electrical specifications 2.4 Electrical characteristics curves Figure 7. Off-state output current IL(off1) (uA) 2.5 2.25 Off state 2 Vcc=36V Vin=Vout=0V 1.75 1.5 1.25 1 0.75 0.5 0.25 0 -50 - Figure 9. Input clamp voltage Vicl ...
Page 15
VN610SP Figure 13 LIM case Ilim ( Vcc=13V -50 - Figure 15. Input high level Vih (V) 3.6 3.4 3.2 3 2.8 ...
Page 16
Application information 3 Application information Figure 19. Application schematic + 3.1 GND protection network against reverse battery This section provides two solutions for implementing a ground protection network against reverse battery. 3.1.1 Solution 1: a resistor in ...
Page 17
VN610SP If the calculated power dissipation requires the use of a large resistor, or several devices have to share the same resistor, then ST suggests using solution 2 below. 3.1.2 Solution 2: a diode (D A resistor (R GND an ...
Page 18
Application information 3.4 Maximum demagnetization energy (V Figure 20. Maximum turn-off current versus load inductance (A) 1000 100 single pulse repetitive pulse repetitive pulse at T ...
Page 19
VN610SP 4 Package and PCB thermal data 4.1 PowerSO-10 thermal data Figure 21. PowerSO-10 PC board Note: Layout condition of R thickness = 2mm, Cu thickness = 35µm, Copper areas: from minimum pad-lay-out to 8cm Figure 22. R thj-amb RTHj_amb ...
Page 20
Package and PCB thermal data Figure 23. Thermal impedance junction ambient single pulse ° ...
Page 21
VN610SP Table 13. Thermal parameters Area / island ( (°C/W) R2 (°C/W) R3 (°C/W) R4 (°C/W) R5 (°C/W) R6 (°C/W) C1 (W.s/°C) C2 (W.s/°C) C3 (W.s/°C) C4 (W.s/°C) C5 (W.s/°C) C6 (W.s/°C) Doc ID 6236 Rev 4 ...
Page 22
Package and packing information 5 Package and packing information ® 5.1 ECOPACK In order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions ...
Page 23
VN610SP Table 14. PowerSO-10 mechanical data Dim (1) L (1) 1. Muar ...
Page 24
Package and packing information 5.3 PowerSO-10 packing information Figure 26. PowerSO-10 suggested pad layout 14.6 - 14 Figure 28. PowerSO-10 tape and reel shipment (suffix “TR”) Tape dimensions According to ...
Page 25
VN610SP 6 Revision history Table 15. Document revision history Date 09-Sep-2004 29-Jan-2008 15-Dec-2008 29-Jul-2010 Revision 1 Initial release. Current and voltage convention update (page 2). Configuration diagram (top view) and suggested connections for unused and n.c. pins insertion (page 2). ...
Page 26
... Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...