VN5E010MHTR-E STMicroelectronics, VN5E010MHTR-E Datasheet
VN5E010MHTR-E
Specifications of VN5E010MHTR-E
Available stocks
Related parts for VN5E010MHTR-E
VN5E010MHTR-E Summary of contents
Page 1
Single-channel high-side driver with analog current sense Features Max supply voltage Operating voltage range Typ. ON-state resistance Current limitation (typ) OFF-state supply current 1. Typical value with all loads connected. ■ General – Inrush current active management by power limitation ...
Page 2
Contents Contents 1 Block diagram and pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Electrical specifications . ...
Page 3
VN5E010MH-E List of tables Table 1. Pin functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
List of figures List of figures Figure 1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 5
VN5E010MH-E 1 Block diagram and pin configuration Figure 1. Block diagram Table 1. Pin functions Name V CC OUT GND IN CS CS_DIS 1. Pins 1 and 7 must be externally tied together. Battery connection (1) Power output Ground connection ...
Page 6
Block diagram and pin configuration Figure 2. Configuration diagram (top view) not in scale Table 2. Suggested connections for unused and not connected pins Connection / pin Floating To ground 6/ GND IN Vcc CS ...
Page 7
... These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE program and other relevant quality document. Table 3. ...
Page 8
Electrical specifications Table 3. Absolute maximum ratings (continued) Symbol Electrostatic discharge (human body model: R= 1.5 KΩ; C= 100 pF) – – CS ESD – CS_DIS – OUT – Charge device model (CDM-AEC-Q100-011) ESD T ...
Page 9
VN5E010MH-E 2.3 Electrical characteristics Values specified in this section are for 8 V < V otherwise specified. Table 5. Power section Symbol Parameter V Operating supply voltage CC V Undervoltage shutdown USD Undervoltage shutdown V USDhyst hysteresis R ON-state resistance ...
Page 10
Electrical specifications Table 7. Logic inputs Symbol V Low-level input voltage IL I Low-level input current IL V High-level input voltage IH I High-level input current IH V Input hysteresis voltage I(hyst) V Input clamp voltage ICL V Low-level CS_DIS ...
Page 11
VN5E010MH-E Table 9. Current sense (8 V < V Symbol OUT OUT ( Current sense ratio drift OUT ( Current sense ratio drift 2 2 ...
Page 12
Electrical specifications Table 9. Current sense (8 V < V Symbol Delay response time t from falling edge of DSENSE1H CS_DIS pin Delay response time t from rising edge of DSENSE1L CS_DIS pin Delay response time t from rising edge ...
Page 13
VN5E010MH-E Figure 5. Switching characteristics V OUT dV OUT INPUT Figure 6. Delay response time between rising edge of ouput current and rising edge of current sense (CS enabled OUT I SENSE t Won 80% /dt (on) ...
Page 14
Electrical specifications Figure 7. Output voltage drop limitation Figure 8. I OUT I /I OUT SENSE 12800 11600 10400 9200 8000 6800 5600 4400 3200 2000 -2 A: Max Max Typical, T 14/ ...
Page 15
VN5E010MH-E Figure 9. Maximum current sense ratio drift vs. load current dK/K (%) -10 -15 - Max Parameter guaranteed by design not tested. Table 10. Truth table Conditions ...
Page 16
Electrical specifications Table 11. Electrical transient requirements (part 1) ISO 7637-2: 2004(E) Test pulse ( The above test levels must be considered referred Valid in case of external load dump ...
Page 17
VN5E010MH-E 2.4 Waveforms Figure 10. Normal operation INPUT INPUT I I OUT OUT V V SENSE SENSE V V CS_DIS CS_DIS Figure 11. Overload or short to GND INPUT INPUT I I LimH LimH I I OUT OUT V V ...
Page 18
Electrical specifications Figure 12. Intermittent overload INPUT INPUT I I LimH LimH I I OUT OUT V V SENSEH SENSEH V V SENSE SENSE V V CS_DIS CS_DIS Figure 13. T evolution in overload or short to GND J INPUT ...
Page 19
VN5E010MH-E 2.5 Electrical characteristics curves Figure 14. OFF-state output current Iloff [nA] 6000 5000 4000 3000 2000 1000 0 -50 - [°C] Figure 16. Input clamp voltage Vicl [V] 7 6.8 6.6 Iin ...
Page 20
Electrical specifications Figure 20. ON-state resistance vs. T Ron [m Ohm ] Iout= 6A Vcc= 13V -50 - [°C] Figure 22. Undervoltage shutdown Vusd [V] 16 ...
Page 21
VN5E010MH-E Figure 26. High-level CS_DIS voltage Vcsdh [V] 4 3.5 3 2.5 2 1.5 1 0.5 0 -50 - [°C] Figure 28. Low-level CS_DIS voltage Vcsdl [V] 4 3.5 3 2.5 2 1.5 1 0.5 0 ...
Page 22
Electrical specifications 2.6 Application information Figure 29. Application schematic +5V MCU C ext 2.7 Load dump protection D is necessary (voltage transient suppressor) if the load dump peak voltage exceeds the ld V max DC rating. The same applies if ...
Page 23
VN5E010MH-E 2.9 Current sense and diagnostic The current sense pin performs a double function (see diagnostic): Current mirror of the load current in normal operation, delivering a current ● proportional to the load one according to a know ratio K ...
Page 24
Electrical specifications 2.10 Maximum demagnetization energy (V Figure 31. Maximum turn-off current versus inductance 100 150 °C (single pulse) jstart 100 °C (repetitive pulse) jstart 125 °C (repetitive ...
Page 25
VN5E010MH-E 3 Package and PC board thermal data 3.1 HPAK thermal data Figure 32. PC board 1. Layout condition of Rth and Zth measurements (PCB FR4 area = mm, PCB thickness =1.8 mm, Cu thickness = ...
Page 26
Package and PC board thermal data Figure 34. HPAK thermal impedance junction ambient single pulse ZTH (°C/W) 100 10 1 0.1 0.001 Figure 35. Thermal fitting model of a single-channel HSD in HPAK 1. The fitting model is a simplified ...
Page 27
VN5E010MH-E Table 14. Thermal parameter Area/island (cm R1 (°C/W) R2 (°C/W) R3 (°C/W) R4 (°C/W) R5 (°C/W) R6 (°C/W) C1 (W.s/°C) C2 (W.s/°C) C3 (W.s/°C) C4 (W.s/°C) C5 (W.s/°C) C6 (W.s/°C) Package and PC board thermal data 2 ) Footprint ...
Page 28
Package and packing information 4 Package and packing information ® 4.1 ECOPACK In order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions ...
Page 29
VN5E010MH-E Table 15. HPAK mechanical data Ref. dim (L1 Package and packing information Data book mm Nom. Min. 2.20 ...
Page 30
Package and packing information 4.3 HPAK suggested land pattern Figure 37. HPAK suggested pad layout 1. The land pattern proposed is not intended to overrule User's PCB design, manufacturing and soldering process rules 30/34 (1) All dimensions are in mm. ...
Page 31
VN5E010MH-E 4.4 Packing information The devices can be packed in tube or tape and reel shipments (see summary). Figure 38. HPAK tube shipment (no suffix) Figure 39. HPAK tape and reel (suffix “TR”) TAPE DIMENSIONS According to Electronic Industries Association ...
Page 32
... Order codes 5 Order codes Table 16. Device summary Package 6 pins HPAK 32/34 Order codes Tube VN5E010MH-E Doc ID 15681 Rev 5 VN5E010MH-E Tape and reel VN5E010MHTR-E ...
Page 33
VN5E010MH-E 6 Revision history Table 17. Document revision history Date 28-May-2009 18-Jun-2009 15-Dec-2009 25-Jan-2010 27-May-2010 Revision 1 Initial release. (1) Figure 32: PC board 2 – Changed footnote 3 Updated Table 7: Logic inputs 4 Updated Table 9: Current sense ...
Page 34
... Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...