VN5010AKTR-E STMicroelectronics, VN5010AKTR-E Datasheet

Page 1

... Thermal shutdown with automatic restart allows the device to recover normal operation as soon as fault condition disappears. Tube VN5010AK-E Doc ID 13218 Rev 6 VN5010AK-E for automotive applications TM PowerSSO-24 pin voltage clamp protects the CC Order codes Tape and reel VN5010AKTR-E Figure 26) 1/31 www.st.com 1 ...

Page 2

Contents Contents 1 Block diagram and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Electrical ...

Page 3

VN5010AK-E List of tables Table 1. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 4

List of figures List of figures Figure 1. Connection diagram (top view ...

Page 5

VN5010AK-E 1 Block diagram and pin description Figure 1. Block diagram GND INPUT CS_DIS Table 2. Pin function Name V CC OUTPUT GND INPUT CURRENT SENSE CS_DIS V CC CLAMP DRIVER LOGIC Pwr Battery connection. Power output. Ground connection. Must ...

Page 6

Block diagram and pin description Figure 2. Connection diagram (top view) CURRENT SENSE Table 3. Suggested connections for unused and not connected pins Connection/pin Floating To ground 1. Not recommended. 6/ GND ...

Page 7

... These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to the conditions in this section for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. Table 4. ...

Page 8

Electrical specifications Table 4. Absolute maximum ratings (continued) Symbol V Current sense maximum voltage CSENSE Maximum switching energy (single pulse) E MAX (L=1.25mH; R Electrostatic discharge (Human Body Model: R=1.5KΩ; C=100pF) – Input – Current Sense V ESD – CS_DIS ...

Page 9

VN5010AK-E Table 6. Power section (continued) Symbol Parameter Off-state output I L(off) current Output - voltage 1. PowerMOS leakage included. Table 7. Switching (V Symbol t Turn-on delay time d(on) t Turn-off delay time d(off) Turn-on voltage ...

Page 10

Electrical specifications Table 9. Protections and diagnostics Symbol I Short circuit current limH Short circuit current during I limL thermal cycling T Shutdown temperature TSD T Reset temperature R T Thermal reset of STATUS RS T Thermal hysteresis (T HYST ...

Page 11

VN5010AK-E Table 10. Current sense (8V<V Symbol Current sense ratio ( drift Analog sense I SENSE0 leakage current Openload on-state I current detection OL threshold Max analog sense V SENSE output voltage Analog sense output V ...

Page 12

Electrical specifications Figure 4. Current sense delay characteristics INPUT CS_DIS LOAD CURRENT SENSE CURRENT Figure 5. Delay response time between rising edge of output current and rising edge of Current Sense (CS enabled OUT I SENSE 12/31 ...

Page 13

VN5010AK-E Figure 6. I OUT I /I OUT SENSE 6000 max Tj = -40°C to 150°C 5500 5000 max Tj= 25°C to 150°C 4500 min Tj= 25°C to 150°C 4000 min Tj= -40°C to 150°C 3500 3000 ...

Page 14

Electrical specifications Table 11. Truth table Conditions Normal operation Overtemperature Undervoltage Short circuit to GND ≤ 10 mΩ Short circuit Negative output voltage clamp 1. If the V is high, the SENSE output is at ...

Page 15

VN5010AK-E Figure 9. Output voltage drop limitation Table 12. Electrical transient requirements (part 1/3) ISO 7637-2: 2004(E) Test pulse (2) 5b Table 13. Electrical transient requirements (part 2/3) ISO 7637-2: 2004(E) Test pulse 1 2a ...

Page 16

Electrical specifications Table 14. Electrical transient requirements (part 3/3) Class C All functions of the device are performed as designed after exposure to disturbance. One or more functions of the device are not performed as designed after exposure to E ...

Page 17

VN5010AK-E Figure 10. Waveforms INPUT CS_DIS LOAD CURRENT SENSE CURRENT V CC INPUT CS_DIS LOAD CURRENT SENSE CURRENT INPUT CS_DIS LOAD VOLTAGE LOAD CURRENT SENSE CURRENT T j INPUT CS_DIS LOAD CURRENT SENSE CURRENT NORMAL OPERATION UNDERVOLTAGE V USDhyst V ...

Page 18

Electrical specifications 2.3 Electrical characteristics curves Figure 11. Off-state output current Iloff (uA) 0.7 0.6 Off state 0.5 Vcc=13V Vin=Vout=0V 0.4 0.3 0.2 0.1 0 -50 - (°C) Figure 13. Input clamp voltage Vicl (V) ...

Page 19

VN5010AK-E Figure 17. On-state resistance vs T Ron (mOhm Iout=6A 40 Vcc=13V -50 - (°C) Figure 19. Undervoltage shutdown Vusd ( ...

Page 20

Electrical specifications Figure 23. CS_DIS high level voltage Vcsdh (V) 4 3.5 3 2.5 2 1.5 1 0.5 0 -50 - (°C) Figure 25. CS_DIS low level voltage Vcsdl (V) 4 3.5 3 2.5 2 ...

Page 21

VN5010AK-E 3 Application information Figure 26. Application schematic +5V mC 3.1 GND protection network against reverse battery 3.1.1 Solution 1: resistor in the ground line (R This can be used with any type of load. The following is an indication ...

Page 22

Application information 3.1.2 Solution 2: diode (D A resistor (R =1 kΩ) should be inserted in parallel to D GND inductive load. This small signal diode can be safely shared amongst several different HSDs. Also in this case, the presence ...

Page 23

VN5010AK-E 3.4 Maximum demagnetization energy (V Figure 27. Maximum turn-off current versus load inductance 100 0 150°C single pulse jstart 100°C repetitive pulse jstart 125°C repetitive pulse jstart ...

Page 24

Package and PCB thermal data 4 Package and PCB thermal data 4.1 PowerSSO-24 Figure 28. PowerSSO-24 Note: Layout condition of R area mm, PCB thickness=1.6mm, Cu thickness=70 µm (front and back side), Copper areas: from minimum ...

Page 25

VN5010AK-E Figure 30. PowerSSO-24 ZTH ( ° 1000 100 10 1 0,1 0,01 1E- 04 0,001 Equation 1: pulse calculation formula ⋅ δ THδ TH where δ Figure 31. Thermal fitting ...

Page 26

Package and PCB thermal data Table 15. Thermal parameters Area/island (cm R1 (°C/W) R2 (°C/W) R3 (°C/W) R4 (°C/W) R5 (°C/W) R6 (°C/W) C1 (W.s/°C) C2 (W.s/°C) C3 (W.s/°C) C4 (W.s/°C) C5 (W.s/°C) C6 (W.s/°C) 26/ Footprint 0.08 ...

Page 27

VN5010AK-E 5 Package and packing information ® 5.1 ECOPACK In order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status ...

Page 28

Package and packing information Table 16. PowerSSO-24™ mechanical data Symbol 28/31 Millimeters Min. Typ. 2.15 0 0.33 ...

Page 29

VN5010AK-E 5.2 Packing information Figure 33. PowerSSO-24 C Figure 34. PowerSSO-24 TAPE DIMENSIONS According to Electronic Industries Association (EIA) Standard 481 rev. A, Feb 1986 Tape width Tape Hole Spacing Component Spacing Hole Diameter Hole Diameter Hole Position Compartment Depth ...

Page 30

Revision history 6 Revision history Table 17. Document revision history Date 24-Jan-2006 09-Feb-2007 13-Dec-2007 12-Feb-2008 16-Jun-2009 16-Jul-2009 30/31 Revision 1 Initial release. Reformatted and restructured. 2 Added Contents, List of tables and List of figures. Added Section 3.4: Maximum demagnetization ...

Page 31

... VN5010AK-E Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...