TLE6209R Infineon Technologies, TLE6209R Datasheet - Page 7

• Manufacturer Part Number: TLE6209R
• Description: IC H-BRIDGE 7A DC MOTOR PDSO-20
• Manufacturer: Infineon Technologies
• Type: Half Bridge DC Motor Driverr

Specifications of TLE6209R

• Applications: DC Motor Driver, H Bridge
• Number Of Outputs: 1
• Current - Output: 6A
• Voltage - Supply: 4.4 V ~ 40 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: DSO-20
• Operating Supply Voltage: 5.2 V to 40 V
• Supply Current: 5 mA
• Mounting Style: SMD/SMT
• Packages: PG-DSO-20
• Current Limit (min.): 5.95 A
• Rthjc (max): 1.5 K/W
• Quiescent Current (max.): 50 µA
• Operating Range: 5.2 - 40 V
• Rds (on) (typ./switch): 140.0 mOhm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Load: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: SP000013299; SP000304414; TLE6209R; TLE6209RNT; TLE6209RT; TLE6209RTR; TLE6209RXT

Table 5
Bit 2
1
1
2.2
2.2.1
The logic is supplied with 5 V by the
The advantage of this system is that information stored in the logic remains intact even
in the event of failures in the supply voltage
be read out via the SPI. If
internally stored data is deleted and the Output Stages are switched to tristate. The IC is
restarted on rising
After this restart at increasing
inhibit mode (INH L to H), the IC is initialized by Power-On-Reset (POR). After POR, all
SPI control bits are set to L. This setting remains valid until first SPI communication. Also
the error bits are reset by POR.
2.2.2
The power stages are connected to the supply voltage
over voltage (OV) and under voltage (UV) comparators as described in Section 2.5.6.
The power supply voltage needs a blocking capacitor to GND.
2.3
2.3.1
The INH input can be used to cut off the complete IC. By pulling the INH input to low, the
power stages are switched to tristate, and the current consumption is reduced to just a
few μA at both the
TLE 6209 R is reinitialized with POR if INH is put to high again. The pin has an internal
pull-down.
2.3.2
The DIS input can be used to disable the output stages. By pulling the DIS input to high
the power stages are switched to tristate, regardless of the signals at the DIR and PWM
inputs. The DIS input can be used as an emergency disable without resetting the SPI
data stored in the IC. It has an internal pull-up.
Data Sheet, Version 3.2
Logic Supply Voltage, Power-On-Reset
Power Supply Voltage
Inhibit (sleep mode)
Disable
Supply
Direct Inputs
Temperature Monitoring
V
V
CC
S
and the
Bit 1
0
1
with a hysteresis of typically 80 mV
V
CC
V
V
CC
CC
falls below typically 4.5 V, the logic is shut down, all
, or if the device is activated after having been set into
input. It also leads to the loss of any data stored. The
V
CC
pin, separated from the power stage supply
7
V
Chip Temperature
Temperature Warning
Overtemperature Shutdown
S
. The power supply failure information can
V
S
. This voltage is monitored by
TLE 6209 R
2010-09-10
V
S
.