LTC1143LCS-ADJ#PBF Linear Technology, LTC1143LCS-ADJ#PBF Datasheet - Page 12

• Manufacturer Part Number: LTC1143LCS-ADJ#PBF
• Description: IC SW REG STEP-DOWN DUAL 16-SOIC
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LTC1143LCS-ADJ#PBF

• Internal Switch(s): No
• Synchronous Rectifier: No
• Number Of Outputs: 2
• Voltage - Output: Adjustable
• Current - Output: 50mA
• Frequency - Switching: 400kHz
• Voltage - Input: 3.5 ~ 16 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (3.9mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -

APPLICATIONS
LTC1143/LTC1143L
LTC1143L-ADJ
Aluminum electrolytic and dry tantalum capacitors are
both available in surface mount configurations. In the case
of tantalum it is critical that the capacitors are surge tested
for use in switching power supplies. An excellent choice is
the AVX TPS series of surface mount tantalums, available
in case heights ranging from 2mm to 4mm. For example,
if 200 F/10V is called for in an application requiring 3mm
height, (2) AVX 100 F/10V (P/N TPSD 107M010) could be
used. Consult the manufacturer for other specific
recommendations.
At low supply voltages a minimum capacitance at C
needed to prevent an abnormal low frequency operating
mode (see Figure 4). When C
output ripple at low frequencies will be large enough to trip
the voltage comparator. This causes Burst Mode operation
to be activated when the LTC1143 series would normally
be in continuous operation. The output remains in
regulation at all times.
Checking Transient Response
The regulator loop response can be checked by looking at
the load transient response. Switching regulators take
several cycles to respond to a step in DC (resistive) load
current. When a load step occurs, V
amount equal to I
series resistance of C
discharge C
current change and returns V
12
1000
800
600
400
200
OUT
Figure 4. Minimum Value of C
0
0
until the regulator loop adapts to the
LOAD
U
1
OUT
L = 25 H
R
R
V
SENSE
SENSE
IN
. I
– V
INFORMATION
U
ESR, where ESR is the effective
L = 50 H
OUT
2
= 0.02
= 0.05
LOAD
L = 50 H
R
OUT
SENSE
VOLTAGE (V)
OUT
to its steady-state value.
3
also begins to charge or
= 0.02
is made too small the
W
4
OUT
OUT
1143 F04
shifts by an
5
U
OUT
is
During this recovery time V
overshoot or ringing which would indicate a stability
problem. The Pin 15(7) external components shown in the
Figure 1 circuit will prove adequate compensation for
most applications.
A second, more severe transient is caused by switching in
loads with large (>1 F) supply bypass capacitors. The
discharged bypass capacitors are effectively put in parallel
with C
deliver enough current to prevent this problem if the load
switch resistance is low and it is driven quickly. The only
solution is to limit the rise time of the switch drive so that
the load rise time is limited to approximately 25 • C
Thus a 10 F capacitor would require a 250 s rise time,
limiting the charging current to about 200mA.
Efficiency Considerations
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can be
expressed as:
where L1, L2, etc. are the individual losses as a percentage
of input power. (For high efficiency circuits only small
errors are incurred by expressing losses as a percentage
of output power.)
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of the
losses in LTC1143 series circuits:
1) The DC supply current is the current that flows into
%Efficiency = 100% – (L1 + L2 + L3 + ...)
V
V
for no load and increases proportionally with load up to
a constant 1.6mA after the LTC1143 series has entered
continuous mode. Because the DC bias current is
IN
IN
1) DC bias current
2) MOSFET gate charge current
3) I
4) Voltage drop of the Schottky diode.
OUT
(Pin 13 and Pin 5) less the gate charge current. For
= 10V the DC supply current for each section is 160 A
2
causing a rapid drop in V
R losses
OUT
can be monitored for
OUT
. No regulator can
LOAD
.