MT9LSDT3272Y-133D2 Micron Technology Inc, MT9LSDT3272Y-133D2 Datasheet

Page 1

SDRAM RDIMM MT9LSDT1672 – 128MB MT9LSDT3272 – 256MB For component data sheets, refer to Micron’s Web site: Features • 168-pin, PC133-compliant registered dual in-line memory module (RDIMM) • Phase-lock loop (PLL) clock driver to reduce loading • Uses 133 MHz ...

Page 2

... Part Number MT9LSDT3272G-13E__ MT9LSDT3272Y-13E__ MT9LSDT3272G-133__ MT9LSDT3272Y-133__ Notes: 1. Data sheets for the base devices can be found on Micron’s Web site. 2. All part numbers end with a two-place code (not shown) that designates component and PCB revisions. Consult factory for current revision codes. Example: MT9LSDT3272G-133D2. ...

Page 3

Pin Assignments and Descriptions Figure 3: Pin Assignments 168-Pin SDRAM RDIMM Front Pin Symbol Pin Symbol Pin Symbol Pin Symbol CB1 DQ0 DQ1 DQ2 25 ...

Page 4

Table 5: Pin Descriptions Symbol Type A0–A12 Input BA0, BA1 Input CK0–CK3 Input CKE0 Input DQMB0–DQMB7 Input RAS#, CAS#, WE# Input REGE Input S0#, S2# Input SA0–SA2 Input SCL Input CB0–CB7 Input/ Output DQ0–DQ63 Input/ Output SDA Input/ Output V ...

Page 5

Functional Block Diagrams Figure 4: Functional Block Diagram – Standard Layout RS0# RDQMB0 V SS RDQMB1 RS2# RDQMB2 V SS RDQMB3 U5, U7 RAS# R CAS# e CKE0 g WE# i A0–A11/A12 s BA0 t e BA1 r S0#, S2# ...

Page 6

Figure 5: Functional Block Diagram – Low Profile Layout RS0# RDQMB0 V SS RDQMB1 RS2# RDQMB2 V SS RDQMB3 U11, U12 RAS# R CAS# e CKE0 g WE# i A0–A11/A12 s BA0 t e BA1 r S0#, S2# s DQMB0–DQMB7 ...

Page 7

... LOW), where the input signals pass through the register/buffer to the SDRAM devices on the same clock. A phase-lock loop (PLL) on the modules is used to redrive the clock signals to the SDRAM devices to minimize system clock loading (CK0 is connected to the PLL, and CK1, CK2, and CK3 are terminated) ...

Page 8

... Serial Presence-Detect Operation SDRAM modules incorporate serial presence-detect. The SPD function is implemented using a 2,048-bit EEPROM. This nonvolatile storage device contains 256 bytes. The first 128 bytes are programmed by Micron to identify the module type and various SDRAM organizations and timing parameters. The remaining 128 bytes of storage are available for use by the customer ...

Page 9

... Ambient operating temperature (commercial) OPR Design Considerations Micron memory modules are designed to optimize signal integrity through carefully designed terminations, controlled board impedances, routing topologies, trace length matching, and decoupling. However, good signal integrity starts at the system level. Micron encourages designers to simulate the signal characteristics of the system’s memory bus to ensure adequate signal integrity of the entire memory system ...

Page 10

I Specifications DD Table 9: I Specifications and Conditions – 128MB DD Values are shown for the MT48LC16M8A2 SDRAM components only and are computed from values specified in the 128Mb (16 Meg x 8) component data sheet Parameter/Condition Operating current: ...

Page 11

Register and PLL Specifications Table 11: Register Timing Requirements and Switching Characteristics 162835A device or equivalent JESD82-2 Parameter Maximum clock pulse frequency Propagation delay, single rank (CK to output) Propagation delay, dual rank (CK to output) Pulse duration Setup time ...

Page 12

Serial Presence-Detect Table 13: Serial Presence-Detect EEPROM DC Operating Conditions Parameter/Condition Supply voltage Input high voltage: Logic 1; All inputs Input low voltage: Logic 0; All inputs Output low voltage 3mA OUT Input leakage current GND ...

Page 13

Module Dimensions Figure 6: 168-Pin SDRAM RDIMM – Standard Layout U1 U2 2.0 (0.079) R (2X) 3.0 (0.118) D (2X) 3.0 (0.118) TYP 6.35 (0.25) TYP Pin 1 3.0 (0.118) TYP U10 Pin 168 Notes: 1. All dimensions are in ...

Page 14

Figure 7: 168-Pin SDRAM RDIMM – Low Profile Layout 2.0 (0.079) R (2X 3.0 (0.118) D (2X) 3.0 (0.118) TYP 6.35 (0.25) TYP Pin 1 3.0 (0.118) TYP U9 Pin 168 Notes: 1. All dimensions are in millimeters ...