PVG3A502A01R00 Murata Electronics North America, PVG3A502A01R00 Datasheet - Page 4

• Manufacturer Part Number: PVG3A502A01R00
• Description: POT 5K OHM 3MM TRIM 1TRN SMD
• Manufacturer: Murata Electronics North America
• Series: PVG3r

Specifications of PVG3A502A01R00

• Resistance (ohms): 5K
• Power (watts): 0.25W, 1/4W
• Taper: Linear
• Tolerance: ±20%
• Temperature Coefficient: ±150ppm/°C
• Number Of Turns: Single
• Adjustment Type: Top Adjustment
• Mounting Type: Surface Mount
• Resistive Material: Cermet
• Package / Case: Square - 0.142" L x 0.134" W x 0.079" H (3.60mm x 3.40mm x 2.00mm)
• Resistance In Ohms: 5.00K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 490-2254-2

!Note
!Note
1. Store that the temperature is -10 to +40deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. The trimmer potentiometer should not be used under
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. The maximum input current to a trimmer
1. Soldering
(1) Standard soldering condition
(2) Can not be soldered using the flow soldering
(3) The soldering iron should not come in contact
(4) Apply the appropriate amount of solder paste.
Notice (Operating and Storage Conditions)
the relative humidity is 30-85%RH.
the following environmental conditions:
If you use the trimmer potentiometer in an
environment other these listed below, please
consult with Murata factory representative prior to
Notice (Rating)
the power depend on the resistance value.
potentiometer should not exceed (P•R)^1/2 or the
maximum operating voltage, whichever is smaller.
potentiometer should not exceed (P/R)^1/2 or the
allowable wiper current, whichever is smaller.
Notice (Soldering and Mounting)
(a) Reflow soldering :
(b) Soldering iron
Before using other soldering conditions more
than those listed above, please consult with
Murata factory representative prior to using.
If the soldering conditions are not
suitable,e.g., excessive time and/or excessive
temperature, the trimmer potentiometer may
deviate from the specified characteristics.
method. If you use the flow soldering method,
the trimmer potentiometer may not function.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
If the amount of solder paste applied to the
land is insufficient, the required adhesive
strength cannot be obtained. If an excessive
amount of solder paste is applied, solder
bridging or flux overflow to the resistive
element surface can occur.
• Please read rating and !CAUTION (for storage and operating, rating, soldering and mounting, handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specification or transact the approval sheet for product specification before ordering.
Please read rating and !CAUTION (for storage and operating, rating, soldering and mounting, handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specification or to transact the approval sheet for product specificaion before ordering.
Temperature of tip : 260deg. C max.
Soldering time
Diameter of tip
Wattage of iron
Refer to the standard temperature profile.
: 3sec. max.
: 2mm dia. max.
: 30W max.
2. Mounting
3. Cleaning
(1) Corrosive gaseous atmosphere.
(2) In liquid.
(3) Dusty/dirty atmosphere.
(4) Direct sunlight.
(5) Static voltage nor electric/magnetic fields.
(6) Direct sea breeze.
(7) Other variations of the above.
(1) Use our standard land dimension. Excessive land
(2) Do not apply excessive force (preferable 4.9N
(3) Do not warp and/or bend PC board to prevent
(4) In chip placers, the size of the cylindrical
(1) Isopropyl-alcohol and Ethyl-alcohol are
(2) Less than 3 minutes of total cleaning time by
(3) In case of ultra-sonic cleaning method, cleaning
using.
(a) Power
(b) Frequency
(c) Temperature : Ambient temperature
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxie gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
area causes displacement due to effect of the
surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
(Ref.; 500gf) max.), when the trimmer
potentiometer is mounted to the PCB.
trimmer potentiometer from breakage.
pick-up nozzle should be outer dimension
2.5-2.8mm dia. and inner dimension
2.0-2.5mm dia..
applicable solvent for cleaning. If you use any
other types of solvents, please consult with
Murata factory representative prior to using.
dipping, vapor and ultra-sonic method.
condition should be as follows.
Due to ultra-sonic cleaning equipment peculiar
self resonance point and cleaning compatibility
usually depends on the jig construction and/or
: 28kHz
: 600W (67lit.) max.
PVG3 Series Notice
Continued on the following page.
R50E12.pdf 02.9.5
27
4