EVAL-ADN2850-25EBZ Analog Devices Inc, EVAL-ADN2850-25EBZ Datasheet - Page 10

• Manufacturer Part Number: EVAL-ADN2850-25EBZ
• Description: BOARD EVALUATION FOR ADN2850-25
• Manufacturer: Analog Devices Inc

Specifications of EVAL-ADN2850-25EBZ

• Main Purpose: Digital Potentiometer
• Utilized Ic / Part: ADN2850-35
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Secondary Attributes: -
• Embedded: -
• Primary Attributes: -
• Lead Free Status / Rohs Status: Supplier Unconfirmed

Daisy-Chain Operation
The serial data output pin (SDO) serves two purposes. It can be
used to read out the contents of the wiper settings or EEMEM
values using instructions 10 and 9 respectively. If these instruc-
tions are not used, SDO can be used for daisy-chaining multiple
devices in simultaneous operations (see Figure 4). The SDO pin
contains an open-drain N-Ch FET and requires a pull-up resis-
tor if SDO function is used. Users need to tie the SDO pin of
one package to the SDI pin of the next package. Users may need
to increase the clock period because the pull-up resistor and the
capacitive loading at the SDO-SDI interface may induce time
delay to the subsequent devices (see Figure 4). If two ADN2850s
are daisy-chained, a total 48 bits of data is required. The first
24 bits (formatted 4-bit instruction, 4-bit address, and 16-bit
data) go to U2 and the second 24 bits with the same format go
to U1. The CS should be kept low until all 48 bits are clocked into
their respective serial registers. The CS is then pulled high to
complete the operation.
DIGITAL INPUT/OUTPUT CONFIGURATION
All digital inputs are ESD protected. Digital inputs are high
impedance and can be driven directly from most digital sources.
Active at logic low, PR and WP should be biased to V
are not used. There are no internal pull-up resistors present on
any digital input pins. To avoid floating digital pins that may
cause false triggering in a noisy environment, pull-up resistors
should be added to these pins. However, this only applies to the
case where the device will be detached from the driving source
once it is programmed.
The SDO and RDY pins are open-drain digital outputs. Similarly,
pull-up resistors are needed if these functions are used. To optimize
the speed and power trade-off, use 2.2 kΩ pull-up resistors.
The equivalent serial data input and output logic is shown in
Figure 5. The open-drain output SDO is disabled whenever
chip select CS is logic high. ESD protection of the digital inputs
is shown in Figures 6a and 6b.
ADN2850
SCLK
C
MOSI
SS
Figure 4. Daisy-Chain Configuration
SDI
CS
ADN2850
U1
CLK
SDO
V
DD
2.2k
R
P
SDI
ADN2850
CS
U2
SDO
CLK
DD
if they
–10–
SERIAL DATA INTERFACE
The ADN2850 contains a 4-wire, SPI compatible, digital inter-
face (SDI, SDO, CS, and CLK). The 24-bit serial word must be
loaded with MSB first, and the format of the word is shown in
Table I. The Command Bits (C0 to C3) control the operation of
the programmable resistor according to the instruction shown
in Table II. A0 to A3 are assigned for address bits. A0 is used to
address RDAC1 or RDAC2. Addresses 2 to 14 are accessible by
users. Address 15 is reserved for the factory. Table V provides an
address map of the EEMEM locations. The data bits (D0 to D9) are
the values that are loaded into the RDAC registers at instruc-
tion 11. The data bits (D0 to D15) are the values that are loaded
into the EEMEM registers at instruction 3.
The last instruction prior to a period of no programming activity
should be applied with the No Operation (NOP), instruction 0. It
is recommended to do so to ensure minimum power consumption
in the internal logic circuitry
The SPI interface can be used in two slave modes, CPHA = 1,
CPOL = 1 and CPHA = 0, CPOL = 0. CPHA and CPOL refer to
the control bits that dictate SPI timing in these microconverters
and microprocessors: ADuC812/ADuC824, M68HC11,
and MC68HC16R1/916R1.
Figure 6a. Equivalent ESD Digital Input Protection
CLK
SDI
CS
Figure 5. Equivalent Digital Input-Output Logic
Figure 6b. Equivalent WP Input Protection
LOGIC
PINS
WP
COUNTER
COMMAND
VALID
INPUT
300
REGISTER
SERIAL
INPUTS
ADN2850
300
AND ADDRESS
PROCESSOR
PR
COMMAND
DECODE
GND
WP
V
DD
GND
V
DD
SDO
GND
5V
R
PULLUP
REV. B