EVAL-ADN2850-25EBZ Analog Devices Inc, EVAL-ADN2850-25EBZ Datasheet - Page 14

• Manufacturer Part Number: EVAL-ADN2850-25EBZ
• Description: BOARD EVALUATION FOR ADN2850-25
• Manufacturer: Analog Devices Inc

Specifications of EVAL-ADN2850-25EBZ

• Main Purpose: Digital Potentiometer
• Utilized Ic / Part: ADN2850-35
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Secondary Attributes: -
• Embedded: -
• Primary Attributes: -
• Lead Free Status / Rohs Status: Supplier Unconfirmed

ADN2850
EEMEM PROTECTION
The write protect ( WP ) pin disables any changes to the
scratchpad register contents, except for the EEMEM setting,
which can still be restored using Instruction 1, Instruction 8,
and the PR pulse. Therefore, WP can be used to provide a
hardware EEMEM protection feature.
DIGITAL INPUT AND OUTPUT CONFIGURATION
All digital inputs are ESD protected, high input impedance that
can be driven directly from most digital sources. Active at logic
low, PR and WP must be tied to V
internal pull-up resistors are present on any digital input pins.
To avoid floating digital pins that might cause false triggering
in a noisy environment, add pull-up resistors. This is applicable
when the device is detached from the driving source when it is
programmed.
The SDO and RDY pins are open-drain digital outputs that only
need pull-up resistors if these functions are used. To optimize
the speed and power trade-off, use 2.2 kΩ pull-up resistors.
The equivalent serial data input and output logic is shown in
Figure 25. The open-drain output SDO is disabled whenever
chip-select ( CS ) is in logic high. ESD protection of the digital
inputs is shown in
CLK
SDI
CS
LOGIC
PINS
Figure 25. Equivalent Digital Input and Output Logic
Figure 26. Equivalent ESD Digital Input Protection
COUNTER
COMMAND
Figure 26
VALID
REGISTER
SERIAL
and
INPUTS
AND ADDRESS
ADN2850
PROCESSOR
300Ω
PR
COMMAND
DECODE
Figure 27
DD
, if they are not used. No
WP
.
GND
V
DD
SDO
GND
5V
R
(FOR DAISY
CHAIN ONLY)
PULL-UP
Rev. C | Page 14 of 28
SERIAL DATA INTERFACE
The ADN2850 contains a 4-wire SPI-compatible digital
interface (SDI, SDO, CS , and CLK). The 24-bit serial data-word
must be loaded with MSB first. The format of the word is shown in
Table 7
digital resistor according to the command shown in
to A3 are the address bits. A0 is used to address RDAC1 or RDAC2.
Address 2 to Address 14 are accessible by users for extra EEMEM.
Address 15 is reserved for factory usage.
address map of the EEMEM locations. D0 to D9 are the values
for the RDAC registers. D0 to D15 are the values for the EEMEM
registers.
The ADN2850 has an internal counter that counts a multiple of
24 bits (a frame) for proper operation. For example, ADN2850
works with a 24-bit or 48-bit word, but it cannot work properly
with a 23-bit or 25-bit word. To prevent data from mislocking
(due to noise, for example), the counter resets, if the count is not a
multiple of four when CS goes high but remains in the register if it
is multiple of four. In addition, the ADN2850 has a subtle
feature that, if CS is pulsed without CLK and SDI, the part
repeats the previous command (except during power-up). As a
result, care must be taken to ensure that no excessive noise exists in
the CLK or CS line that might alter the effective number-of-bits
pattern.
The SPI interface can be used in two slave modes: CPHA = 1,
CPOL = 1 and CPHA = 0, CPOL = 0. CPHA and CPOL refer to
the control bits that dictate SPI timing in the following
MicroConverters® and microprocessors: ADuC812, ADuC824,
M68HC11, MC68HC16R1, and MC68HC916R1.
DAISY-CHAIN OPERATION
The serial data output pin (SDO) serves two purposes. It can be
used to read the contents of the wiper setting and EEMEM values
using Instruction 10 and Instruction 9, respectively. The remaining
instructions (Instruction 0 to Instruction 8, Instruction 11 to
Instruction 15) are valid for daisy-chaining multiple devices in
simultaneous operations. Daisy-chaining minimizes the number
of port pins required from the controlling IC (see Figure 28). The
SDO pin contains an open-drain N-Ch FET that requires a pull-up
resistor, if this function is used. As shown in Figure 28, users need
to tie the SDO pin of one package to the SDI pin of the next package.
Users may need to increase the clock period because the pull-up
. The command bits (C0 to C3) control the operation of the
WP
Figure 27. Equivalent WP Input Protection
INPUT
300Ω
Table 10
GND
V
DD
provides an
Table 8
. A0