EVAL-ADN2850-25EBZ Analog Devices Inc, EVAL-ADN2850-25EBZ Datasheet - Page 9

• Manufacturer Part Number: EVAL-ADN2850-25EBZ
• Description: BOARD EVALUATION FOR ADN2850-25
• Manufacturer: Analog Devices Inc

Specifications of EVAL-ADN2850-25EBZ

• Main Purpose: Digital Potentiometer
• Utilized Ic / Part: ADN2850-35
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Secondary Attributes: -
• Embedded: -
• Primary Attributes: -
• Lead Free Status / Rohs Status: Supplier Unconfirmed

Table 5. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Mnemonic
SDO
GND
V
V1
W1
B1
B2
W2
V2
V
WP
PR
CS
RDY
CLK
SDI
EP
SS
DD
Description
Serial Data Output. Serves readback and daisy-chain functions. Command 9 and Command 10 activate the SDO
output for the readback function, delayed by 24 or 25 clock pulses, depending on the clock polarity before and
after the data-word (see Figure 2 and Figure 3). In other commands, the SDO shifts out the previously loaded SDI
bit pattern, delayed by 24 or 25 clock pulses depending on the clock polarity (see Figure 2 and Figure 3). This
previously shifted out SDI can be used for daisy-chaining multiple devices. Whenever SDO is used, a pull-up
resistor in the range of 1 kΩ to 10 kΩ is needed.
Ground Pin, Logic Ground Reference.
Negative Supply. Connect to 0 V for single-supply applications. If V
2 mA for 15 ms when storing data to EEMEM.
Log Output Voltage 1. Generates voltage from an internal diode configured transistor.
Wiper terminal of RDAC1. ADDR (RDAC1) = 0x0.
Terminal B of RDAC1.
Terminal B of RDAC2.
Wiper terminal of RDAC2. ADDR (RDAC2) = 0x1.
Log Output Voltage 2. Generates voltage from an internal diode configured transistor.
Positive Power Supply.
Optional Write Protect. When active low, WP prevents any changes to the present contents, except PR strobe.
CMD_1 and COMD_8 refresh the RDAC register from EEMEM. Tie WP to V
Optional Hardware Override Preset. Refreshes the scratchpad register with current contents of the EEMEM
register. Factory default loads midscale until EEMEM is loaded with a new value by the user. PR is activated
at the logic high transition. Tie PR to V
Serial Register Chip Select Active Low. Serial register operation takes place when CS returns to logic high.
Ready. Active high open-drain output. Identifies completion of Instruction 2, Instruction 3, Instruction 8,
Instruction 9, Instruction 10, and PR.
Serial Input Register Clock. Shifts in one bit at a time on positive clock edges.
Serial Data Input. Shifts in one bit at a time on positive clock CLK edges. MSB loads first.
Exposed Pad. The exposed pad is left floating or is tied to V
INDICATOR
NOTES
1. THE EXPOSED PAD IS LEFT FLOATING
GND
OR IS TIED TO V
SDO
V
V
PIN 1
SS
1
Figure 5. Pin Configuration
1
2
3
4
Rev. C | Page 9 of 28
DD
(Not to Scale)
ADN2850
TOP VIEW
, if not used.
(EXPOSED
PAD)
SS
.
12 PR
11 WP
10 V
9 V
SS
DD
2
.
SS
is used in dual supply, it must be able to sink
DD
, if not used.
ADN2850