DEMO9S08SG32AUTO Freescale Semiconductor, DEMO9S08SG32AUTO Datasheet

DEMO9S08SG32AUTO

Manufacturer Part Number

DEMO9S08SG32AUTO

Description

DEMO BOARD FOR MC9S08SG32

Manufacturer

Freescale Semiconductor

Type

MCUr

Datasheets

1.DEMO9S08SG32AUTO.pdf (15 pages)

2.DEMO9S08SG32AUTO.pdf (2 pages)

Specifications of DEMO9S08SG32AUTO

Contents

Processor To Be Evaluated

MC9S08Sx

Data Bus Width

8 bit

Interface Type

RS-232, USB

Silicon Manufacturer

Freescale

Core Architecture

HCS08

Core Sub-architecture

HCS08

Silicon Core Number

MC9S08

Silicon Family Name

S08SG

Kit Contents

Board

Rohs Compliant

Yes

For Use With/related Products

MC9S08SG32

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 2
Download datasheet (34Kb)

D E M O 9 S 0 8 S H 3 2 / S G 3 2

Q U I C K

DEMO9S08SH32/SG32 QUICK START GUIDE

Introduction and Default Settings

This quick start guide will show how to connect the target board to a PC, install the correct version of CodeWarrior

Development Studio, and execute a simple demonstration program loaded in FLASH memory. The default

jumper settings for the DEMO9S08SH32/SG32 are shown below

Install CodeWarrior Development Studio for HC(S)08 Special Edition

To install CodeWarrior Development Studio for HC(S)08 Special Edition, refer to the “CodeWarrior Development

Studio” DVD case and follow the steps in the included Quick Start Guide.

CodeWarrior Development Studio must be properly installed before attempting to connect the target board to the

host PC. Otherwise, the necessary USB drivers will not be available and the host PC will not recognize the target

board when connected.

Run the LED_DEMO Program

The DEMO9S08SH32/SG32 ships with a simple demonstration program loaded into on-chip FLASH memory.

This demonstration program executes when power is applied or when the RESET button is pressed. The source

code for this demo program can be found in the LED_DEMO.zip file on the Axiom Support CD in the /Examples

folder. Follow the steps below to run the LED_DEMO program.

1. Verify the configuration jumpers are set to the default position. Refer to Figure 1 above.

2. Connect the included USB cable between an open USB port on the host PC and the USB connector on the

3. Follow the on-screen instructions to install the necessary USB drivers.

4. After the USB drivers are properly installed, the USB, POWER OUT, and +5V LED’s will be ON.

5. The LED_DEMO program will execute - LED1 toggles at approximately 4Hz. LED2 toggles each time SW2 is

target board.

pressed.

S T A R T

G U I D E

Figure 1: DEMO9S08SH32/SG32 Default Settings

R E V

D O C - 0 4 2 1 - 0 2 0

1 . 1 ,

Spencer Ruggles

0 7 / 2 0 0 7

Related parts for DEMO9S08SG32AUTO

DEMO9S08SG32AUTO Summary of contents

Page 1

DEMO9S08SH32/SG32 QUICK START GUIDE Introduction and Default Settings ...

Page 2

Load and run the LED_DEMO Program The steps ...

Related keywords

demo9s08sg
demo9s08sh
demo9s08sg8
demo9s08sg32
demo9s12xsfame
demo9s12xep100
demo9s12xdt512
demo9s12ne64
demo9s08sv16
demo9s08se
demo9s08sc4
demo9s08ll16
DEMO9S08SG32AUTO datasheet
DEMO9S08SG32AUTO data sheet
DEMO9S08SG32AUTO pdf datasheet
DEMO9S08SG32AUTO component
DEMO9S08SG32AUTO part
DEMO9S08SG32AUTO distributor
DEMO9S08SG32AUTO RoHS
DEMO9S08SG32AUTO datasheet download