EL5177 INTERSIL [Intersil Corporation], EL5177 Datasheet
EL5177
Available stocks
Related parts for EL5177
EL5177 Summary of contents
Page 1
... Both outputs (OUT+, OUT-) are short circuit protected to withstand temporary overload condition. The EL5177 is available in the 10 Ld MSOP package and is specified for operation over the full -40°C to +85°C temperature range. See also EL5174 (EL5177 MSOP.) ...
Page 2
... Common Mode Negative Input Range Positive Reference Input Voltage Range REFIN 2 EL5177 Thermal Information = +25°C) Recommended Operating Temperature . . . . . . . . . .-40°C to +85°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +135° 0.8V (max) Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C S Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp = T ...
Page 3
... I EN Pin Input Current Low IL-EN Pin Descriptions PIN NUMBER PIN NAME 1 FBP 2 IN+ 3 REF 4 IN- 5 FBN 6 OUT VS+ 9 VS- 10 OUT+ 3 EL5177 - = -5V +25° 0V 1kΩ CONDITIONS + = REF V = ±2. 500Ω to GND 10Ω ...
Page 4
... 50pF 34pF 9pF 2.7pF -10 1M 10M FREQUENCY (Hz) FIGURE 3. FREQUENCY RESPONSE EL5177 R F1 0Ω 1 FBP OUT IN+ VS REF VS+ 8 OPEN 4 IN FBN OUT 0Ω = 200mV ...
Page 5
... FREQUENCY (Hz) FIGURE 7. FREQUENCY RESPONSE - V 100 -20 1K 10K 100K 1M FREQUENCY (Hz) FIGURE 9. CMRR vs FREQUENCY 5 EL5177 (Continued 1kΩ F 100M 400M 10M 100M REF 10M 100M 1G FIGURE 10. VOLTAGE AND CURRENT NOISE vs FREQUENCY 2.7pF 750Ω ...
Page 6
... HD3 (f = 20MHz) -55 -60 -65 -70 -75 -80 -85 -90 HD2 (f = 5MHz) -95 -100 200 300 400 500 600 700 R (Ω) LD FIGURE 15. HARMONIC DISTORTION EL5177 (Continued) 10M 100M FIGURE 12. HARMONIC DISTORTION vs DIFFERENTIAL -50 -55 -60 -65 -70 -75 -80 -85 -90 -95 HD2 (f = 5MHz) -100 -100 800 900 1000 FIGURE 16 ...
Page 7
... JA 0.3 0.2 0 AMBIENT TEMPERATURE (°C) FIGURE 21. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE 7 EL5177 (Continued) 0.5V/DIV FIGURE 18. LARGE SIGNAL TRANSIENT RESPONSE CH1 CH2 85 100 125 FIGURE 22. PACKAGE POWER DISSIPATION vs AMBIENT 10ns/DIV M = 400ns, CH1 = 200mV/DIV, CH2 = 5V/DIV 400ns/DIV FIGURE 20. DISABLED RESPONSE ...
Page 8
... The output of the EL5177 can swing from -3.8V to +3.8V at 1kΩ differential load at ±5V supply. As the load resistance becomes lower, the output swing is reduced. Differential and Common Mode Gain Settings The voltage applied at REF pin can set the output common mode voltage and the gain is one ...
Page 9
... Again, a small series resistor at the output can help to reduce peaking. Disable/Power-Down The EL5177 can be disabled and placed its outputs in a high impedance state. The turn off time is about 1.2µs and the turn on time is about 130ns. When disabled, the amplifier's supply current is reduced to 1.7µA for I typically, thereby effectively eliminating the power consumption ...
Page 10
... The feedback resistor should be placed very close to the inverting input pin. Strip line design techniques are recommended for the signal traces TWISTED PAIR EL5177 100Ω FIGURE 24. TWISTED PAIR CABLE RECEIVER ...
Page 11
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 11 EL5177 MDP0043 A MINI SO PACKAGE FAMILY ...