el5371 Intersil Corporation, el5371 Datasheet
el5371
Available stocks
Related parts for el5371
el5371 Summary of contents
Page 1
... Generally, these pins are grounded but can be tied to any voltage reference. All outputs are short circuit protected to withstand temporary overload condition. The EL5171 and EL5371 are specified for operation over the full -40°C to +85°C temperature range. Ordering Information PART PART TAPE & ...
Page 2
... IN DMIR Differential Mode Input Range CMIR+ Common Mode Positive Input Range at V CMIR- Common Mode Negative Input Range Positive Reference Input Voltage Range (EL5371) REFIN 2 EL5171, EL5371 = +25°C) Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +135°C Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85° ...
Page 3
... OUT R Output Impedance OUT SUPPLY V Supply Operating Range SUPPLY I Power Supply Current - Per Channel S(ON Positive Power Supply Current - Disabled (EL5371) EN pin tied to 4.8V S(OFF Negative Power Supply Current - Disabled (EL5371) S(OFF) PSRR Power Supply Rejection Ratio ENABLE (EL5371 ONLY) t Enable Time EN t Disable Time ...
Page 4
... EL5171 R F1 -5V 1 FBP OUT 8 2 INP VSN REF VSP FBN OUTB 5 50Ω 50Ω +5V EL5371 + OUT1 28 2 INP1 FBP1 INN1 FBN1 26 REF1 OUT1B VSP 24 6 INP2 VSN 23 INN2 OUT2 7 ...
Page 5
... C = 2.7pF 200Ω 10M FREQUENCY (Hz) FIGURE 5. FREQUENCY RESPONSE 5 EL5171, EL5371 V = 200mV OP P-P 100M 1G FIGURE 2. FREQUENCY RESPONSE FOR VARIOUS GAIN = 1kΩ 500Ω LD 100M 1kΩ 500Ω F 100M 400M R = 1kΩ ...
Page 6
... PSRR+ -60 -70 -80 -90 100K 1K 10K 1M FREQUENCY (Hz) FIGURE 9. PSRR vs FREQUENCY 1K 100 100 1K 10K FREQUENCY (Hz) FIGURE 11. VOLTAGE AND CURRENT NOISE vs FREQUENCY 6 EL5171, EL5371 (Continued) 100M REF 100 10M 100M -100 100K 1M 10M 100 10 1 0.1 10K 100K 1M 10M FREQUENCY (Hz) FIGURE 8. OUTPUT IMPEDANCE vs FREQUENCY ...
Page 7
... OP- for OP- -40 HD3 (A -50 -60 -70 -80 -90 -100 FREQUENCY (MHz) FIGURE 17. HARMONIC DISTORTION vs FREQUENCY 7 EL5171, EL5371 (Continued) 4 4.5 5 FIGURE 14. HARMONIC DISTORTION vs DIFFERENTIAL 700 800 900 1000 for 50mV/DIV FIGURE 18. SMALL SIGNAL TRANSIENT RESPONSE V = ± ...
Page 8
... Typical Performance Curves 0.5V/DIV 10ns/DIV FIGURE 19. LARGE SIGNAL TRANSIENT RESPONSE M = 200ns, CH1 = 500mV/DIV, CH2 = 5V/DIV CH1 CH2 200ns/DIV FIGURE 21. DISABLED RESPONSE FIGURE 23. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE 8 EL5171, EL5371 (Continued) CH1 CH2 1.2 0.8 0.6 0.4 0.2 FIGURE 22. PACKAGE POWER DISSIPATION vs AMBIENT JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD 1 ...
Page 9
... REF pin is from -3.3V to 3.8V. If the input common mode or differential mode signal is outside the above-specified ranges, it will cause the output signal distorted. The output of the EL5171 and EL5371 can swing from -3.9V to +3.9V at 1kΩ differential load at ±5V supply. As the load resistance becomes lower, the output swing is reduced. 9 ...
Page 10
... Disable/Power-Down (for EL5371 only The EL5371 can be disabled and placed its outputs in a high impedance state. The turn off time is about 0.95µs and the turn on time is about 215ns. When disabled, the amplifier's supply current is reduced to 1.7µA for I typically, thereby effectively eliminating the power consumption ...
Page 11
... T G IN- REF FBN 11 EL5171, EL5371 Power Supply Bypassing and Printed Circuit Board Layout As with any high frequency device, a good printed circuit board layout is necessary for optimum performance. Lead lengths should be as sort as possible. The power supply pin must be well bypassed to reduce the risk of oscillation. For normal single supply operation, where the V connected to the ground plane, a single 4.7µ ...
Page 12
... NOTE: The package drawing shown here may not be the latest version. To check the latest revision, please refer to the Intersil website at http://www.intersil.com/design/packages/index.asp 12 EL5171, EL5371 this loss is to boost the high frequency gain at the receiver side ...
Page 13
... Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 13 EL5171, EL5371 D (N/2)+1 (N/2) H ...
Page 14
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 14 EL5171, EL5371 MDP0040 QUARTER SIZE OUTLINE PLASTIC PACKAGES FAMILY (N/2)+1 ...