ISL8483E Intersil Corporation, ISL8483E Datasheet
ISL8483E
Available stocks
Related parts for ISL8483E
ISL8483E Summary of contents
Page 1
... Specified for 10% Tolerance Supplies • High Data Rate Version (ISL8485E 5Mbps • Slew Rate Limited Version for Error Free Data Transmission (ISL8483E .up to 250kbps • Single Unit Load Allows Devices on the Bus • 1nA Low Current Shutdown Mode (ISL8483E) • ...
Page 2
... GND Truth Tables PKG. DWG. # INPUTS M8. M8. E8.3 1 M8.15 *Shutdown Mode for ISL8483E (see Note 7) M8.15 E8.3 M8. M8. *Shutdown Mode for ISL8483E (see Note 7) FUNCTION TRANSMITTING OUTPUTS ...
Page 3
... Typical Operating Circuits +5V + 0.1µ GND 5 3 ISL8483E, ISL8485E ISL8483E, ISL8485E R T +5V + 0.1µ GND 5 ...
Page 4
... R = 50Ω (RS-422), (Figure 27Ω (RS-485), (Figure 27Ω or 50Ω, (Figure 27Ω or 50Ω, (Figure 27Ω or 50Ω, (Figure 1) OC DE, DI DE, DI DE, DI, RE (ISL8483E) DI (ISL8485E) DE, RE (ISL8485E 0V 12V CC IN 4 -7V IN -7V ≤ ...
Page 5
... (Note 2) (Continued TEST CONDITIONS ISL8485E, DI ISL8483E, DI ISL8483E 0V -7V ≤ V ≤ 12V, (Note ≤ V ≤ 54Ω 100pF, (Figure 2) ...
Page 6
... When testing the ISL8483E, the RE signal high time must be short enough (typically <200ns) to prevent the device from entering SHDN. 7. The ISL8483E is put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 50ns, the parts are guaranteed not to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See “ ...
Page 7
... Test Circuits and Waveforms SIGNAL GENERATOR FIGURE 2A. TEST CIRCUIT FIGURE 2. DRIVER PROPAGATION DELAY AND DIFFERENTIAL TRANSITION TIMES SIGNAL Y GENERATOR C L (SHDN) FOR ISL8483E ONLY PARAMETER OUTPUT Y/Z 0 (Note Y/Z 0 (Note ...
Page 8
... Test Circuits and Waveforms RE B +1. SIGNAL GENERATOR FIGURE 4A. TEST CIRCUIT SIGNAL A GENERATOR (SHDN) FOR ISL8483E ONLY PARAMETER +1. -1. (Note 6) 0 +1. (Note 6) 0 -1. (Note 9) 0 +1.5V ZH(SHDN) t (Note 9) 0 -1.5V ZL(SHDN) FIGURE 5A. TEST CIRCUIT Application Information ...
Page 9
... Disabling both the driver and the receiver for less than 50ns guarantees that the ISL8483E will not enter shutdown. Note that receiver and driver enable times increase when the ISL8483E enables from shutdown. Refer to Notes 5-8, at the end of the Electrical Specification table, for more information. ESD Protection ...
Page 10
... DIFF 3 2 - TEMPERATURE ( C) TEMPERATURE ISL8485E ISL8483E ISL8485E GND ISL8483E GND GND - TEMPERATURE ( C) FIGURE 9. SUPPLY CURRENT vs TEMPERATURE | PHLY PLHZ |t |CROSS PT. OF Y↑ & Z↓ - CROSS PT. OF Y↓ & Z↑| 0 -40 0 ...
Page 11
... TIME (10ns / DIV) FIGURE 16. DRIVER AND RECEIVER WAVEFORMS, LOW TO HIGH (ISL8485E) 11 ISL8483E, ISL8485E 5V ISL8483E and ISL8485E; Unless Otherwise Specified (Continued 2 PLHZ 1 FIGURE 13. DRIVER SKEW vs TEMPERATURE (ISL8485E) = 54Ω 100pF ...
Page 12
... Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): GND TRANSISTOR COUNT: 518 PROCESS: Si Gate CMOS 12 ISL8483E, ISL8485E ...
Page 13
... B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). 13 ISL8483E, ISL8485E E8.3 8 LEAD DUAL-IN-LINE PLASTIC PACKAGE SYMBOL ...
Page 14
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 14 ISL8483E, ISL8485E M8.15 (JEDEC MS-012-AA ISSUE C) 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC ...