PIC24F04KA201-I/SS Microchip Technology, PIC24F04KA201-I/SS Datasheet - Page 58

• Manufacturer Part Number: PIC24F04KA201-I/SS
• Description: IC PIC MCU FLASH 512KX4 20-SSOP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 24Fr

Specifications of PIC24F04KA201-I/SS

• Core Size: 16-Bit
• Program Memory Size: 4KB (1.375K x 24)
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Number Of I /o: 18
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 9x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP
• Controller Family/series: PIC24
• No. Of I/o's: 18
• Ram Memory Size: 512Byte
• Cpu Speed: 32MHz
• No. Of Timers: 3
• Processor Series: PIC24F
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 512 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 32 KHz
• Number Of Programmable I/os: 12
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, DM240001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 9 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC24F04KA201 FAMILY
6.3.5
The oscillator start-up circuitry and its associated delay
timers are not linked to the device Reset delays that
occur at power-up. Some crystal circuits (especially
low-frequency crystals) will have a relatively long
start-up time. Therefore, one or more of the following
conditions is possible after SYSRST is released:
• The oscillator circuit has not begun to oscillate.
• The Oscillator Start-up Timer has not expired (if a
• The PLL has not achieved a lock (if PLL is used).
The device will not begin to execute code until a valid
clock source has been released to the system. There-
fore, the oscillator and PLL start-up delays must be
considered when the Reset delay time must be known.
6.3.6
If the FSCM is enabled, it will begin to monitor the
system clock source when SYSRST is released. If a
valid clock source is not available at this time, the
device will automatically switch to the FRC Oscillator
and the user can switch to the desired crystal oscillator
in the Trap Service Routine (TSR).
DS39937B-page 56
crystal oscillator is used).
POR AND LONG OSCILLATOR
START-UP TIMES
FAIL-SAFE CLOCK MONITOR
(FSCM) AND DEVICE RESETS
Preliminary
DSLPBOR will re-arm the POR to ensure the device will
6.4
Most of the Special Function Registers (SFRs) associ-
ated with the PIC24F CPU and peripherals are reset to a
particular value at a device Reset. The SFRs are
grouped by their peripheral or CPU function and their
Reset values are specified in each section of this manual.
The Reset value for each SFR does not depend on the
type of Reset with the exception of four registers. The
Reset value for the Reset Control register, RCON, will
depend on the type of device Reset. The Reset value
for the Oscillator Control register, OSCCON, will
depend on the type of Reset and the programmed
values of the FNOSC bits in Flash Configuration Word
(FOSCSEL); see Table 6-2. The RCFGCAL and
NVMCON registers are only affected by a POR.
6.5
Deep Sleep BOR is a very low-power BOR circuitry,
used when the device is in Deep Sleep mode. Due to
low-current consumption, accuracy may vary.
The DSBOR trip point is around 2.0V. DSBOR is
enabled by configuring FDS <DSLPBOR> = 1.
reset if V
DD
Special Function Register Reset
States
Deep Sleep BOR (DSBOR)
drops below the POR threshold.
© 2009 Microchip Technology Inc.