AT90PWM3B-16SU Atmel, AT90PWM3B-16SU Datasheet - Page 129

• Manufacturer Part Number: AT90PWM3B-16SU
• Description: IC MCU AVR RISC 8K FLASH 32-SOIC
• Manufacturer: Atmel
• Series: AVR® 90PWM Lightingr

Specifications of AT90PWM3B-16SU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 27
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-SOIC (7.5mm Width)
• Processor Series: AT90PWMx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI/USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 27
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRFBKIT, ATAVRISP2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• On-chip Dac: 1-chx10-bit
• Controller Family/series: AVR PWM
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-SOIC - STK600 SOCKET/ADAPTER FOR SOIC770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRMC200 - KIT EVAL FOR AT90PWM3 ASYNCATAVRFBKIT - KIT DEMO BALLAST FOR AT90PWM2ATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK520 - ADAPTER KIT FOR 90PWM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

16. Power Stage Controller – (PSC0, PSC1 & PSC2)
16.1
16.2
4317J–AVR–08/10
Features
Overview
The Power Stage Controller is a high performance waveform controller.
•
•
•
•
•
•
•
•
•
•
•
•
Many register and bit references in this section are written in general form.
•
•
The purpose of a Power Stage Controller (PSC) is to control power modules on a board. It has
two outputs on PSC0 and PSC1 and four outputs on PSC2.
These outputs can be used in various ways:
•
•
•
Each PSC has two inputs the purpose of which is to provide means to act directly on the gener-
ated waveforms:
•
•
•
•
The PSC can be chained and synchronized to provide a configuration to drive three half bridges.
Thanks to this feature it is possible to generate a three phase waveforms for applications such
as Asynchronous or BLDC motor drive.
PWM waveform generation function (2 complementary programmable outputs)
Dead time control
Standard mode up to 12 bit resolution
Frequency Resolution Enhancement Mode (12 + 4 bits)
Frequency up to 64 Mhz
Conditional Waveform on External Events (Zero Crossing, Current Sensing ...)
All on chip PSC synchronization
ADC synchronization
Overload protection function
Abnormality protection function, emergency input to force all outputs to high impedance or in
inactive state (fuse configurable)
Center aligned and edge aligned modes synchronization
Fast emergency stop by hardware
A lower case “n” replaces the PSC number, in this case 0, 1 or 2. However, when using the
register or bit defines in a program, the precise form must be used, i.e., PSOC1 for
accessing PSC 0 Synchro and Output Configuration register and so on.
A lower case “x” replaces the PSC part , in this case A or B. However, when using the
register or bit defines in a program, the precise form must be used, i.e., PFRCnA for
accessing PSC n Fault/Retrigger n A Control register and so on.
“Two Ouputs” to drive a half bridge (lighting, DC motor ...)
“One Output” to drive single power transistor (DC/DC converter, PFC, DC motor ...)
“Four Outputs” in the case of PSC2 to drive a full bridge (lighting, DC motor ...)
Current sensing regulation
Zero crossing retriggering
Demagnetization retriggering
Fault input
AT90PWM2/3/2B/3B
129