PIC16F747-I/ML Microchip Technology, PIC16F747-I/ML Datasheet - Page 43

• Manufacturer Part Number: PIC16F747-I/ML
• Description: IC PIC MCU FLASH 4KX14 44QFN
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F747-I/ML

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: FLASH
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: AUSART, CCP, I2C, MSSP, SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 8
• Operating Supply Voltage: 4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000, DM163022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• For Use With: XLT44QFN2 - SOCKET TRAN ICE 44QFN/40DIPAC164322 - MODULE SOCKET MPLAB PM3 28/44QFNI3DBF777 - BOARD DAUGHTER ICEPIC3444-1001 - DEMO BOARD FOR PICMICRO MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

4.7
4.7.1
When SCS bits are configured to run from the INTRC,
a clock transition is generated if the system clock is not
already using the INTRC. The event will clear the
OSTS bit and switch the system clock from the primary
system clock (if SCS<1:0> = 00) determined by the
value contained in the configuration bits, or from the
T1OSC (if SCS<1:0> = 01) to the INTRC clock option
and shut-down the primary system clock to conserve
power. Clock switching will not occur if the primary
system clock is already configured as INTRC.
FIGURE 4-7:
 2004 Microchip Technology Inc.
SCS<1:0>
Note 1:
Program
INTOSC
Counter
System
OSC1
Clock
2:
3:
4:
Power-Managed Modes
T
T
T
T
INP
OSC
SCS
DLY
Q1
RC_RUN MODE
T
= 32 s typical.
OSC (2)
= 8 T
= 1 T
Q2
= 50 ns minimum.
PC
Q3
INP
INP
.
.
Q4
TIMING DIAGRAM FOR XT, HS, LP, EC, EXTRC TO RC_RUN MODE
T
Q1
DLY (4)
T
INP
(1)
T
SCS
(3)
PC + 1
If the system clock does not come from the INTRC
(31.25 kHz) when the SCS bits are changed and the
IRCF bits in the OSCCON register are configured for a
frequency other than INTRC, the frequency may not be
stable immediately. The IOFS bit (OSCCON<2>) will
be set when the INTOSC or postscaler frequency is
stable, after 4 ms (approx.).
After a clock switch has been executed, the OSTS bit
is cleared, indicating a low-power mode and the device
does not run from the primary system clock. The inter-
nal Q clocks are held in the Q1 state until eight falling
edge clocks are counted on the INTRC oscillator. After
the eight clock periods have transpired, the clock input
to the Q clocks is released and operation resumes (see
Figure 4-7).
Q1
Q2
Q3
Q4
PIC16F7X7
Q1
Q2
PC + 2
DS30498C-page 41
Q3
Q4
PC + 3
Q1