ST72F264G1M6 STMicroelectronics, ST72F264G1M6 Datasheet - Page 30

• Manufacturer Part Number: ST72F264G1M6
• Description: IC MCU 8BIT 4K 28 SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F264G1M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: ST72F2x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7F264-IND/USB, ST72F34X-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit
• For Use With: 497-6423 - BOARD EVAL BASED ON ST72264G1497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-2105-5

ST72260Gx, ST72262Gx, ST72264Gx
INTERRUPTS (Cont’d)
7.3 INTERRUPTS AND LOW POWER MODES
All interrupts allow the processor to exit the WAIT
low power mode. On the contrary, only external
and other specified interrupts allow the processor
to exit the HALT modes (see column “Exit from
HALT” in “Interrupt Mapping” table). When several
pending interrupts are present while exiting HALT
mode, the first one serviced can only be an inter-
rupt with exit from HALT mode capability and it is
selected through the same decision process
shown in
Note: If an interrupt, that is not able to Exit from
HALT mode, is pending with the highest priority
when exiting HALT mode, this interrupt is serviced
after the first one serviced.
Figure 18. Concurrent Interrupt Management
Figure 19. Nested Interrupt Management
30/172
Figure
11 / 10
11 / 10
MAIN
MAIN
RIM
RIM
17.
IT2
IT2
IT1
IT1
IT4
TLI
TLI
IT1
IT4
IT0
IT0
7.4 CONCURRENT & NESTED MANAGEMENT
The following
different interrupt management modes. The first is
called concurrent mode and does not allow an in-
terrupt to be interrupted, unlike the nested mode in
Figure
in this order from the lowest to the highest: MAIN,
IT4, IT3, IT2, IT1, IT0. The software priority is giv-
en for each interrupt.
Warning: A stack overflow may occur without no-
tifying the software of the failure.
Note: TLI (Top Level Interrupt) is not available in
this product.
Related Documentation
AN1044: Multiple interrupt source management
for ST7 MCUs
IT3
IT3
IT1
19. The interrupt hardware priority is given
IT4
IT2
Figure 18
10
10
SOFTWARE
PRIORITY
LEVEL
SOFTWARE
PRIORITY
LEVEL
MAIN
MAIN
and
3
3
3
3
3
3
3/0
3
3
2
1
3
3
3/0
Figure 19
I1
I1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
0 0
0 1
1 1
1 1
show two
I0
I0