MC908GP32CPE Freescale Semiconductor, MC908GP32CPE Datasheet - Page 150

• Manufacturer Part Number: MC908GP32CPE
• Description: IC MCU 8MHZ 32K FLASH 40-DIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GP32CPE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 33
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: HC08GP
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Serial Communications Interface Module (SCI)
13.8.4 SCI Status Register 1
SCI status register 1 (SCS1) contains flags to signal these conditions:
SCTE — SCI Transmitter Empty Bit
TC — Transmission Complete Bit
SCRF — SCI Receiver Full Bit
IDLE — Receiver Idle Bit
150
•
•
•
•
•
•
•
•
This clearable, read-only bit is set when the SCDR transfers a character to the transmit shift register.
SCTE can generate an SCI transmitter CPU interrupt request. When the SCTIE bit in SCC2 is set,
SCTE generates an SCI transmitter CPU interrupt request. In normal operation, clear the SCTE bit by
reading SCS1 with SCTE set and then writing to SCDR. Reset sets the SCTE bit.
This read-only bit is set when the SCTE bit is set, and no data, preamble, or break character is being
transmitted. TC generates an SCI transmitter CPU interrupt request if the TCIE bit in SCC2 is also set.
TC is automatically cleared when data, preamble or break is queued and ready to be sent. There may
be up to 1.5 transmitter clocks of latency between queueing data, preamble, and break and the
transmission actually starting. Reset sets the TC bit.
This clearable, read-only bit is set when the data in the receive shift register transfers to the SCI data
register. SCRF can generate an SCI receiver CPU interrupt request. When the SCRIE bit in SCC2 is
set, SCRF generates a CPU interrupt request. In normal operation, clear the SCRF bit by reading
SCS1 with SCRF set and then reading the SCDR. Reset clears SCRF.
This clearable, read-only bit is set when 10 or 11 consecutive logic 1s appear on the receiver input.
IDLE generates an SCI receiver CPU interrupt request if the ILIE bit in SCC2 is also set. Clear the IDLE
bit by reading SCS1 with IDLE set and then reading the SCDR. After the receiver is enabled, it must
1 = SCDR data transferred to transmit shift register
0 = SCDR data not transferred to transmit shift register
1 = No transmission in progress
0 = Transmission in progress
1 = Received data available in SCDR
0 = Data not available in SCDR
Transfer of SCDR data to transmit shift register complete
Transmission complete
Transfer of receive shift register data to SCDR complete
Receiver input idle
Receiver overrun
Noisy data
Framing error
Parity error
Address:
Reset:
Read:
Write:
$0016
SCTE
Bit 7
1
Figure 13-12. SCI Status Register 1 (SCS1)
= Unimplemented
TC
6
1
MC68HC908GP32 Data Sheet, Rev. 10
SCRF
5
0
IDLE
4
0
OR
3
0
NF
2
0
FE
1
0
Freescale Semiconductor
Bit 0
PE
0