MC56F8147VPYE Freescale Semiconductor, MC56F8147VPYE Datasheet - Page 30

• Manufacturer Part Number: MC56F8147VPYE
• Description: IC DSP 16BIT 40MHZ 160-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8147VPYE

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 76
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Ram Size: 4K x 16
• Voltage - Supply (vcc/vdd): 2.25 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 160-LQFP
• Data Bus Width: 16 bit
• Processor Series: MC56F81xx
• Core: 56800E
• Data Ram Size: 4 KB
• Interface Type: SPI, SCI, CAN
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 76
• Number Of Timers: 2
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4 x 12 bit, 4 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

30
Table 2-2 Signal and Package Information for the 160-Pin LQFP and MBGA (Continued)
Signal Name
(GPIOE5)
(GPIOE6)
(GPIOE7)
MOSI0
MISO0
SS0
148
147
145
Pin
No.
Ball
No.
D5
B6
D4
Output
Output
Output
Output
Output
Input/
Input/
Input/
Input/
Input/
Type
Input
56F8347 Technical Data, Rev.11
disabled,
pull-up is
output is
In reset,
enabled
enabled
enabled
During
pull-up
pull-up
Reset
Input,
Input,
State
SPI 0 Slave Select — SS0 is used in slave mode to indicate
to the SPI module that the current transfer is to be received.
Port E GPIO — This GPIO pin can be individually
programmed as input or output pin.
After reset, the default state is SS0.
To deactivate the internal pull-up resistor, clear bit 7 in the
GPIOE_PUR register.
SPI 0 Master Out/Slave In — This serial data pin is an
output from a master device and an input to a slave device.
The master device places data on the MOSI line a half-cycle
before the clock edge the slave device uses to latch the data.
Port E GPIO — This GPIO pin can be individually
programmed as an input or output pin.
After reset, the default state is MOSI0.
To deactivate the internal pull-up resistor, clear bit 5 in the
GPIOE_PUR register.
SPI 0 Master In/Slave Out — This serial data pin is an input
to a master device and an output from a slave device. The
MISO line of a slave device is placed in the high-impedance
state if the slave device is not selected. The slave device
places data on the MISO line a half-cycle before the clock
edge the master device uses to latch the data.
Port E GPIO — This GPIO pin can be individually
programmed as an input or output pin.
After reset, the default state is MISO0.
To deactivate the internal pull-up resistor, clear bit 6 in the
GPIOE_PUR register.
Signal Description
Freescale Semiconductor
Preliminary