ATTINY48-MMHR Atmel, ATTINY48-MMHR Datasheet - Page 207

• Manufacturer Part Number: ATTINY48-MMHR
• Description: MCU AVR 4KB FLASH 12MHZ 28QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY48-MMHR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 12MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 24
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

T
Notes:
8008G–AVR–04/11
A
Symbol
I
I
R
I
LIL
LIH
CC
PU
= -40°C to +85°C, V
1. Typical values at 25
2. “Max” means the highest value where the pin is guaranteed to be read as low.
3. These parameters are not tested in production.
4. “Min” means the lowest value where the pin is guaranteed to be read as high.
5. Although each I/O port can sink more than the test conditions (10 mA at V
6. The RESET pin must tolerate high voltages when entering and operating in programming modes and, as a consequence,
7. High Sink I/O pins are PD0, PD1, PD2 and PD3.
8. Although each I/O port can source more than the test conditions (10 mA at V
9. These are test limits, which account for leakage currents of the test environment. Actual device leakage currents are lower.
10. Values are with external clock using methods described in
11. Measured with Brown-Out Detection (BOD) disabled.
under steady state conditions (non-transient), the following must be observed:
• The sum of all I
• The sum of all I
If I
than the listed test condition.
has a weak drive strength as compared to regular I/O pins. See
ure 23-38
under steady state conditions (non-transient), the following must be observed:
• The sum of all I
• The sum of all I
If II
greater than the listed test condition.
enabled (PRR = 0xFF) and there is no I/O drive.
Parameter
Input Leakage
Current I/O Pin
Input Leakage
Current I/O Pin
Pull-up Resistor, I/O Pin
Pull-up Resistor, Reset Pin
Supply Current,
Active Mode
Supply Current,
Idle Mode
Supply Current,
Power-down Mode
OL
OH
exceeds the test condition, V
exceeds the test condition, V
and
CC
(10)
Figure 23-39
= 1.8V to 5.5V (unless otherwise noted) (Continued)
OL
OL
OH
OH
, for ports A0, A3, B0 – B7, C7, D5 – D7 should not exceed 100 mA.
, for ports A1 – A2, C0 – C6, D0 – D4 should not exceed 100 mA.
, for ports A2 – A3, B0 – B7, C6, D0 – D7 should not exceed 100 mA.
, for ports A0 – A1, C0 – C5, C7 should not exceed 100 mA.
°
(11)
C.
(starting on
Condition
V
(absolute value)
V
(absolute value)
V
V
f = 1MHz, V
f = 4MHz, V
f = 8MHz, V
f = 1MHz, V
f = 4MHz, V
f = 8MHz, V
WDT enabled, V
WDT disabled, V
CC
CC
CC
CC
OL
OH
= 5.5V, pin low
= 5.5V, pin high
= 5.5V, input low
= 5.5V, input low
may exceed the related specification. Pins are not guaranteed to sink current greater
may exceed the related specification. Pins are not guaranteed to source current
page
CC
CC
CC
CC
CC
CC
= 2V
= 3V
= 5V
= 2V
= 3V
= 5V
236).
CC
CC
= 3V
= 3V
“Minimizing Power Consumption” on page
Figure
Min
20
30
23-34,
CC
CC
= 5V, 5 mA at V
Figure
Typ
< 0.05
< 0.05
= 5V, 5mA at V
< 0.2
0.03
0.25
0.2
1.4
4.5
1
4
(1)
23-35,
Figure
CC
CC
= 3V, 2 mA at V
Max
1
1
0.4
2.5
0.1
0.6
= 3V, 2 mA at V
50
60
10
8
2
2
ATtiny48/88
23-36,
(9)
(9)
38. Power reduction is
Figure
CC
Units
23-37,
CC
mA
mA
mA
mA
mA
mA
kΩ
kΩ
µA
µA
µA
µA
= 1.8V)
= 1.8V)
207
Fig-