PIC18F65J10-I/PT Microchip Technology, PIC18F65J10-I/PT Datasheet - Page 253

• Manufacturer Part Number: PIC18F65J10-I/PT
• Description: IC PIC MCU FLASH 16KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F65J10-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SPI/I2C/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 50
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183022, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180015 - MODULE PLUG-IN 18F87J10 FOR HPCAC162062 - HEADER INTRFC MPLAB ICD2 64/80PAC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

19.3
The Synchronous Master mode is entered by setting
the CSRC bit (TXSTAx<7>). In this mode, the data is
transmitted in a half-duplex manner (i.e., transmission
and reception do not occur at the same time). When
transmitting data, the reception is inhibited and vice
versa. Synchronous mode is entered by setting bit
SYNC (TXSTAx<4>). In addition, enable bit SPEN
(RCSTAx<7>) is set in order to configure the TXx and
RXx pins to CKx (clock) and DTx (data) lines,
respectively.
The Master mode indicates that the processor trans-
mits the master clock on the CKx line. Clock polarity is
selected with the SCKP bit (BAUDCONx<4>); setting
SCKP sets the Idle state on CKx as high, while clearing
the bit sets the Idle state as low. This option is provided
to support Microwire devices with this module.
19.3.1
The EUSART transmitter block diagram is shown in
Figure 19-3. The heart of the transmitter is the Transmit
(Serial) Shift Register (TSR). The Shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREGx. The TXREGx register is loaded with data in
software. The TSR register is not loaded until the last
bit has been transmitted from the previous load. As
soon as the last bit is transmitted, the TSR is loaded
with new data from the TXREGx (if available).
FIGURE 19-11:
© 2006 Microchip Technology Inc.
RC7/RX1/DT1
RC6/TX1/CK1 pin
(SCKP = 0)
RC6/TX1/CK1 pin
(SCKP = 1)
Write to
TXREG1 Reg
TX1IF bit
(Interrupt Flag)
TRMT bit
TXEN bit
Note: Sync Master mode, SPBRGx = 0, continuous transmission of two 8-bit words. This example is equally applicable to EUSART2
(RG1/TX2/CK2 and RG2/RX2/DT2).
EUSART Synchronous
Master Mode
EUSART SYNCHRONOUS MASTER
TRANSMISSION
Q1 Q2 Q3Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4
‘1’
Write Word 1
SYNCHRONOUS TRANSMISSION
bit 0
Write Word 2
bit 1
Word 1
bit 2
Preliminary
Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Once the TXREGx register transfers the data to the
TSR register (occurs in one T
and the TXxIF flag bit is set. The interrupt can be
enabled or disabled by setting or clearing the interrupt
enable bit, TXxIE. TXxIF is set regardless of the state
of enable bit TXxIE; it cannot be cleared in software. It
will reset only when new data is loaded into the
TXREGx register.
While flag bit TXxIF indicates the status of the TXREGx
register, another bit, TRMT (TXSTAx<1>), shows the
status of the TSR register. TRMT is a read-only bit which
is set when the TSR is empty. No interrupt logic is tied to
this bit, so the user must poll this bit in order to determine
if the TSR register is empty. The TSR is not mapped in
data memory so it is not available to the user.
To set up a Synchronous Master Transmission:
1.
2.
3.
4.
5.
6.
7.
8.
bit 7
Initialize the SPBRGHx:SPBRGx registers for the
appropriate baud rate. Set or clear the BRG16
bit, as required, to achieve the desired baud rate.
Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
If interrupts are desired, set enable bit TXxIE.
If 9-bit transmission is desired, set bit TX9.
Enable the transmission by setting bit TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Start transmission by loading data to the
TXREGx register.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
bit 0
Word 2
bit 1
PIC18F87J10
CY
), the TXREGx is empty
DS39663D-page 251
bit 7
‘1’