PIC18F6490-E/PT Microchip Technology, PIC18F6490-E/PT Datasheet - Page 159

• Manufacturer Part Number: PIC18F6490-E/PT
• Description: IC PIC MCU FLASH 16KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6490-E/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, LCD, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 64-TFQFP
• For Use With: DM163028 - BOARD DEMO PICDEM LCD
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

15.0
15.1
The Master Synchronous Serial Port (MSSP) module is
a serial interface, useful for communicating with other
peripheral or microcontroller devices. These peripheral
devices may be serial EEPROMs, shift registers,
display drivers, A/D converters, etc. The MSSP module
can operate in one of two modes:
• Serial Peripheral Interface (SPI)
• Inter-Integrated Circuit (I
The I
hardware:
• Master mode
• Multi-Master mode
• Slave mode
15.2
The MSSP module has three associated registers.
These include a status register (SSPSTAT) and two
control registers (SSPCON1 and SSPCON2). The use
of these registers and their individual Configuration bits
differ significantly depending on whether the MSSP
module is operated in SPI or I
Additional details are provided under the individual
sections.
© 2007 Microchip Technology Inc.
- Full Master mode
- Slave mode (with general address call)
2
C interface supports the following modes in
MASTER SYNCHRONOUS
SERIAL PORT (MSSP)
MODULE
Master SSP (MSSP) Module
Overview
Control Registers
2
C)
2
C mode.
PIC18F6390/6490/8390/8490
15.3
The SPI mode allows 8 bits of data to be synchronously
transmitted and received simultaneously. All four
modes
communication, typically three pins are used:
• Serial Data Out (SDO) – RC5/SDO/SEG12
• Serial Data In (SDI) – RC4/SDI/SDA
• Serial Clock (SCK) – RC3/SCK/SCL
Additionally, a fourth pin may be used when in a Slave
mode of operation:
• Slave Select (SS) – RF7/SS/SEG25
Figure 15-1 shows the block diagram of the MSSP
module when operating in SPI mode.
FIGURE 15-1:
RC5/SDO/SEG12
RC3/SCK/
RC4/SDI/SDA
SCL
RF7/SS/
SEG25
SPI Mode
of
SPI
Read
are
Select
SMP:CKE
SS Control
Edge
MSSP BLOCK DIAGRAM
(SPI MODE)
Select
Edge
bit 0
Enable
Data to TXx/RXx in SSPSR
supported.
TRIS bit
2
SSPM3:SSPM0
SSPBUF reg
SSPSR reg
Clock Select
4
2
DS39629C-page 157
To
(
Prescaler
4, 16, 64
TMR2 Output
Write
Clock
Shift
Data Bus
accomplish
Internal
2
T
OSC
)