PIC18F2580-E/SP Microchip Technology, PIC18F2580-E/SP Datasheet - Page 187

• Manufacturer Part Number: PIC18F2580-E/SP
• Description: IC PIC MCU FLASH 16KX16 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2580-E/SP

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: SPI/I2C/MSSP/EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163011, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP280 - DEVICE ADAPTER 18F2220 PDIP 28LD
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

16.4.9
The following steps should be taken when configuring
the ECCP module for PWM operation:
1.
2.
3.
4.
5.
6.
7.
8.
9.
© 2007 Microchip Technology Inc.
Configure the PWM pins P1A and P1B (and
P1C and P1D, if used) as inputs by setting the
corresponding TRIS bits.
Set the PWM period by loading the PR2 register.
Configure the ECCP1 module for the desired
PWM mode and configuration by loading the
ECCP1CON register with the appropriate
values:
• Select one of the available output
• Select the polarities of the PWM output
Set the PWM duty cycle by loading the
ECCPR1L register and ECCP1CON<5:4> bits.
For
dead-band delay by loading ECCP1DEL<6:0>
with the appropriate value.
If auto-shutdown operation is required, load the
ECCP1AS register:
• Select the auto-shutdown sources using the
• Select the shutdown states of the PWM
• Set the ECCPASE bit (ECCP1AS<7>).
• Configure the comparators using the CMCON
• Configure the comparator inputs as analog
If auto-restart operation is required, set the
PRSEN bit (ECCP1DEL<7>).
Configure and start TMR2:
• Clear the TMR2 interrupt flag bit by clearing
• Set the TMR2 prescale value by loading the
• Enable Timer2 by setting the TMR2ON bit
Enable PWM outputs after a new PWM cycle
has started:
• Wait until TMRn overflows (TMRnIF bit is set).
• Enable the ECCP1/P1A, P1B, P1C and/or
• Clear the ECCPASE bit (ECCP1AS<7>).
configurations and direction with the
EPWM1M1:EPWM1M0 bits.
signals with the ECCP1M3:ECCP1M0 bits.
ECCPAS2:ECCPAS0 bits.
output pins using PSSAC1:PSSAC0 and
PSSBD1:PSSBD0 bits.
register.
inputs.
the TMR2IF bit (PIR1<1>).
T2CKPS bits (T2CON<1:0>).
(T2CON<2>).
P1D pin outputs by clearing the respective
TRIS bits.
Half-Bridge
SETUP FOR PWM OPERATION
Output
mode,
set
PIC18F2480/2580/4480/4580
the
Preliminary
16.4.10
Both Power-on Reset and subsequent Resets will force
all ports to Input mode and the CCP registers to their
Reset states.
This forces the Enhanced CCP module to reset to a
state compatible with the standard CCP module.
EFFECTS OF A RESET
DS39637C-page 185