PIC14000-20/SS Microchip Technology, PIC14000-20/SS Datasheet - Page 26

• Manufacturer Part Number: PIC14000-20/SS
• Description: IC MCU OTP 4KX14 A/D 28SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 14r

Specifications of PIC14000-20/SS

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C
• Peripherals: POR, Temp Sensor, WDT
• Number Of I /o: 20
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: OTP
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 6 V
• Data Converters: Slope A/D
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-SSOP
• Processor Series: PIC14000
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 192 B
• Interface Type: SPI, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 1
• Operating Supply Voltage: 2.7 V to 6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: 0 C
• On-chip Adc: 14 bit
• For Use With: 309-1025 - ADAPTER 28-SSOP TO 28-DIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC14000
FIGURE 5-2:
5.2
PORTC is a 8-bit wide bidirectional port, with Schmitt
Trigger inputs, that serves the following functions
depending on programming:
• Direct LED drive (PORTC<7:0>).
• I
• Interrupt on change function (PORTC<7:4>),
• Programmable reference and comparator
• Timer0 clock source on RC3
The PORTC data register is located at location 07h and
its data direction register (TRISC) is at 87h.
PORTC<5:0> have weak internal pull-ups (~100 uA
typical). A single control bit can turn on all the pull-ups.
This is done by clearing bit RCPU (OPTION<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are
disabled on power-on reset and in hibernate mode.
DS40122B-page 26
05h
PORTA
Read/Write
POR value 0xh
B7-B4
B3
B2
B1
B0
Section 7.0 I
discussed below and in Section 10.3 Interrupts.
outputs.
2
C communication lines (PORTC<7:6>), refer to
Bit
PORTC and TRISC
2
RA3/AN3
RA2/AN2
RA1/AN1
RA0/AN0
—
C Serial Port.
PORTA DATA REGISTER
Name
Bit 7
—
U
0
Function
Unimplemented. Reads as‘0’.
GPIO or analog input. Returns value on pin RA3/AN3 when used as a digital
input. When configured as an analog input, reads as ‘0’.
GPIO or analog input. Returns value on pin RA2/AN2 when used as a digital
input. When configured as an analog input, reads as ‘0’.
GPIO or analog input. Returns value on RA1/AN1 when used as a digital input.
This pin can connect to a level shift network. If enabled, a +0.5V offset is added
to the input voltage. When configured as an analog input, reads as ‘0’.
GPIO or analog input. Returns value on pin RA0/AN0 when used as a digital
input. When configured as an analog input, reads as ‘0’.
Bit 6
—
U
0
Bit 5
—
U
0
Preliminary
Bit 4
—
U
0
When using PORTC<0> as an analog output
(CMCON<1> bit is set), the TRISC<0> bit should be
cleared to disable the weak pull-up on this pin. Refer to
Table 5-1.
Four of the PORTC pins, RC<7:4> have an interrupt on
change feature. Only pins configured as inputs can
cause this interrupt to occur. In other words, any pin
RC<7:4> configured as an output is excluded from the
interrupt on change comparison. The input pins of
RC<7:4> are compared with the old value latched on
the last read of PORTC. The “mismatch” outputs of
RC<7:4> are OR’ed together to assert the RCIF flag
(PIR1 register<2>) and cause a CPU interrupt, if
enabled.
RA3/AN3
Note:
Bit 3
R/W
X
If
(I
automatically
interrupt-on-change comparison.
2
CCON<5>, address 14h), RC<7:6> are
RA2/AN2
the
Bit 2
R/W
X
I
2
C
1996 Microchip Technology Inc.
function
excluded
RA1/AN1
Bit 1
R/W
X
is
from
RA0/AN0
enabled,
Bit 0
R/W
X
the