STM32F103RBH6 STMicroelectronics, STM32F103RBH6 Datasheet - Page 60

• Manufacturer Part Number: STM32F103RBH6
• Description: MCU ARM 32BIT 128KB FLASH 64BGA
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103RBH6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 51
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-BGA
• Processor Series: STM32F103x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 20 KB
• Interface Type: CAN, I2C, SPI, USART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 51
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, KSDK-STM32-PLUS, KSK-STM32-JL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ST-LINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (12 bit, 16 Channel)
• Featured Product: STM32 Cortex-M3 Companion Products
• Eeprom Size: -
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-8418 - BOARD DEMO DGTL PHOTOFRAME STM32497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Electrical characteristics
5.3.13
Table 35.
1. FT = Five-volt tolerant. In order to sustain a voltage higher than V
2. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization, not tested in production.
3. With a minimum of 100 mV.
4. Leakage could be higher than max. if negative current is injected on adjacent pins.
5. Pull-up and pull-down resistors are designed with a true resistance in series with a switchable PMOS/NMOS. This
60/99
Symbol
V
R
R
C
V
V
I
disabled.
PMOS/NMOS contribution
lkg
hys
PU
PD
IH
IO
IL
Standard IO input low
level voltage
IO FT
voltage
Standard IO input high
level voltage
IO FT
voltage
Standard IO Schmitt
trigger voltage
hysteresis
IO FT Schmitt trigger
voltage hysteresis
Input leakage current
Weak pull-up equivalent
resistor
Weak pull-down
equivalent resistor
I/O pin capacitance
I/O port characteristics
General input/output characteristics
Unless otherwise specified, the parameters given in
performed under the conditions summarized in
compliant.
I/O static characteristics
(1)
(1)
Parameter
(5)
input low level
input high level
(2)
to the series resistance is minimum
(2)
(5)
(4)
V
V
V
DD
DD
Standard I/Os
SS
Conditions
V
V
> 2 V
≤
V
≤
I/O FT
IN
IN
IN
2 V
V
=
=
= 5 V
IN
V
V
≤
DD
Doc ID 13587 Rev 13
SS
V
DD
(~10% order)
0.41*(V
0.42*(V
5% V
DD
DD
+0.3 the internal pull-up/pull-down resistors must be
DD
–0.3
–0.3
Min
200
30
30
-2 V)+1.3 V
Table
-2 V)+1 V
DD
.
(3)
Table 35
9. All I/Os are CMOS and TTL
Typ
40
40
STM32F103x8, STM32F103xB
5
are derived from tests
0.32*(V
0.28*(V
V
DD
DD
DD
Max
5.5
5.2
50
50
±1
-2V)+0.75 V
-2 V)+0.8 V
3
+0.3
Unit
mV
mV
µA
kΩ
kΩ
pF
V
V
V
V