MCHC908MR8CFAE Freescale Semiconductor, MCHC908MR8CFAE Datasheet - Page 265

• Manufacturer Part Number: MCHC908MR8CFAE
• Description: IC MCU 8K FLASH 8MHZ PWM 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCHC908MR8CFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 16
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 16
• Ram Memory Size: 256Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Processor Series: HC08MR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4
• Operating Supply Voltage: 0 V to 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

MC68HC908MR8 — Rev 4.1
Freescale Semiconductor
NOTE:
TXINV — Transmit Inversion Bit
Setting the TXINV bit inverts all transmitted values, including idle, break,
start, and stop bits.
M — Mode (Character Length) Bit
WAKE — Wakeup Condition Bit
ILTY — Idle Line Type Bit
This read/write bit reverses the polarity of transmitted data. Reset
clears the TXINV bit.
This read/write bit determines whether SCI characters are eight or
nine bits long. (See
stop bit, as a receiver wakeup signal, or as a parity bit. Reset clears
the M bit.
This read/write bit determines which condition wakes up the SCI: a
logic 1 (address mark) in the most significant bit (MSB) position of a
received character or an idle condition on the PTB0/RxD pin. Reset
clears the WAKE bit.
This read/write bit determines when the SCI starts counting logic 1s
as idle character bits. The counting begins either after the start bit or
after the stop bit. If the count begins after the start bit, then a string of
logic 1s preceding the stop bit may cause false recognition of an idle
character. Beginning the count after the stop bit avoids false idle
character recognition, but requires properly synchronized
transmissions. Reset clears the ILTY bit.
1 = Transmitter output inverted
0 = Transmitter output not inverted
1 = 9-bit SCI characters
0 = 8-bit SCI characters
1 = Address mark wakeup
0 = Idle line wakeup
1 = Idle character bit count begins after stop bit.
0 = Idle character bit count begins after start bit.
Serial Communications Interface (SCI)
Table
13-4.) The ninth bit can serve as an extra
Serial Communications Interface (SCI)
Technical Data
I/O Registers
265