LH79524N0F100A1,55 NXP Semiconductors, LH79524N0F100A1,55 Datasheet - Page 35

• Manufacturer Part Number: LH79524N0F100A1,55
• Description: IC ARM7 BLUESTREAK MCU 208LFBGA
• Manufacturer: NXP Semiconductors
• Series: BlueStreak ; LH7r

Specifications of LH79524N0F100A1,55

• Core Processor: ARM7
• Core Size: 32-Bit
• Speed: 76.2MHz
• Connectivity: EBI/EMI, Ethernet, I²C, IrDA, Microwire, SPI, SSI, SSP, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, LCD, POR, PWM, WDT
• Number Of I /o: 108
• Program Memory Type: ROMless
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.7 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-LFBGA
• For Use With: SDK-LH79524-10-3216R - KIT DEVELOPMENT ZOOM SDK LH79524460-3474 - KIT DEV ZOOM STARTER FOR LH79524568-4305 - BOARD EVAL FOR LH79524
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Other names: 568-4272; 935285053551; LH79524N0F100A1-S

System-on-Chip
NOTES:
1. The timing relationship is specified as a cycle-based timing. Variations caused by clock jitter, power rail noise, and I/O conditioning will cause
2. The Read Wait States register (SWAITRDx) must be set to a minimum value of 3.
3. For each rising clock edge (HCLK) that the assertion of nWAIT lags the assertion of nCSx, another read wait state (SWAITRDx) must be
4. nWAIT delay cycles are not added for all nWAIT assertions sampled prior to WST-3. These nWAIT assertions are ignored.
5. nWAIT delay cycles are added for all nWAIT assertions sampled from WST-3 until the de-assertion of nWAIT. nWAIT delay cycles are added
6. Once nWAIT is sampled high, the current memory transaction is queued to complete.
7. Since static and dynamic memory cannot be accessed at the same time, any prolonged access (either due to nWAIT or the Extended Wait
8. Timing assumes Output Enable Delay register (SWAITOENx) is programmed to 0.
Preliminary data sheet
tDA_nCS(x)_nWAIT
tDD_nWAIT_nCS(x)
tDD_nWAIT_nOE
tA_nWAIT
NOTES:
SQ: nWAIT Sampled and Queued
SI: nWAIT Sampled and Ignored
these timings to vary nominally. It is recommended that designers add a small margin to avoid possible corner-case conditions.
added to the minimum requirement.
once the wait state countdown has reached WST-1.
Register) that causes an SDRAM refresh failure may cause SDRAM data to be lost.
nCS(x)
nWAIT
HCLK
Transaction
Sequence
nOE
PARAMETER
tDA_nCS(x)_nWAIT
DELAY
WST-3
Delay from nCS(x) assertion to nWAIT assertion
Delay from nWAIT deassertion to nCS(x) deassertion
Delay from nWAIT deassertion to nOE deassertion
Assertion time of nWAIT
SQ-4
Table 16. nWAIT Read Sequence Parameter Definitions
DELAY
WST-2
Figure 11. nWAIT Read Sequence (SWAITRDx = 3)
SQ-3
DELAY
WST-1
tA_nWAIT
SQ-2
NXP Semiconductors
DELAY
nWAIT
Rev. 01 — 16 July 2007
SQ-4
DESCRIPTION
SQ-1
DELAY
nWAIT
SQ-3
SQ-0
DELAY
nWAIT
SQ-2
DELAY
nWAIT
tDD_nWAIT_nCS(x)
SQ-1
tDD_nWAIT_nOE
DELAY
nWAIT
SQ-0
MIN.
0
2
DELAY
WST-0
16,365
MAX.
4
4
LH79524/LH79525
HCLK periods
HCLK periods
HCLK periods
HCLK periods
UNIT
LH79525-133
1
35