MC9S08RD32CPE Freescale Semiconductor, MC9S08RD32CPE Datasheet - Page 174

• Manufacturer Part Number: MC9S08RD32CPE
• Description: IC MCU 32K FLASH 2K RAM 28-DIP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08RD32CPE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -

Serial Peripheral Interface (SPI) Module
BIDIROE — Bidirectional Mode Output Enable
SPISWAI — SPI Stop in Wait Mode
SPC0 — SPI Pin Control 0
13.4.3
This register is used to set the prescaler and bit rate divisor for an SPI master. This register may be read or
written at any time.
SPPR2:SPPR1:SPPR0 — SPI Baud Rate Prescale Divisor
174
When bidirectional mode is enabled by SPI pin control 0 (SPC0) = 1, BIDIROE determines whether
the SPI data output driver is enabled to the single bidirectional SPI I/O pin. Depending on whether the
SPI is configured as a master or a slave, it uses either the MOSI1 (MOMI) or MISO1 (SISO) pin,
respectively, as the single SPI data I/O pin. When SPC0 = 0, BIDIROE has no meaning or effect.
The SPC0 bit chooses single-wire bidirectional mode. If MSTR = 0 (slave mode), the SPI uses the
MISO1 (SISO) pin for bidirectional SPI data transfers. If MSTR = 1 (master mode), the SPI uses the
MOSI1 (MOMI) pin for bidirectional SPI data transfers. When SPC0 = 1, BIDIROE is used to enable
or disable the output driver for the single bidirectional SPI I/O pin.
This 3-bit field selects one of eight divisors for the SPI baud rate prescaler as shown in
input to this prescaler is the bus rate clock (BUSCLK). The output of this prescaler drives the input of
the SPI baud rate divider (see
1 = SPI I/O pin enabled as an output.
0 = Output driver disabled so SPI data I/O pin acts as an input.
1 = SPI clocks stop when the MCU enters wait mode.
0 = SPI clocks continue to operate in wait mode.
1 = SPI configured for single-wire bidirectional operation.
0 = SPI uses separate pins for data input and data output.
SPI Baud Rate Register (SPI1BR)
Reset:
Read:
Write:
Figure 13-9. SPI Baud Rate Register (SPI1BR)
Bit 7
0
0
MC9S08RC/RD/RE/RG Data Sheet, Rev. 1.11
Figure
= Unimplemented or Reserved
<st-blue>
SPPR2
6
0
13-4).
<st-blue>
SPPR1
5
0
<st-blue>
SPPR0
4
0
3
0
0
<st-blue>
SPR2
2
0
<st-blue>
SPR1
Freescale Semiconductor
1
0
Table
<st-blue>
SPR0
Bit 0
0
13-2. The