AT91SAM7S64C-AU Atmel, AT91SAM7S64C-AU Datasheet - Page 141

• Manufacturer Part Number: AT91SAM7S64C-AU
• Description: IC ARM7 MCU 32BIT 64K 64LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7S64C-AU

• Package / Case: 64-LQFP
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Operating Temperature: -40°C ~ 85°C
• Speed: 55MHz
• Number Of I /o: 32
• Core Processor: ARM7
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Program Memory Size: 64KB (64K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Connectivity: I²C, SPI, SSC, UART/USART, USB
• Core Size: 16/32-Bit
• Core: ARM7TDMI
• Package: 64LQFP
• Device Core: ARM7TDMI
• Family Name: AT91
• Maximum Speed: 55 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 32
• Interface Type: SPI/TWI/USART/USB
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: AT91SAM7S64B-AU::AT91SAM7S64B-AU

20.3.4.6
20.3.4.7
6175K–ATARM–30-Aug-10
Flash Security Bit Command
AT91SAM7S512 Select EFC Command
GP NVM bits can be read using Get GPNVM Bit command (GGPB). When a bit set in the Bit
Mask is returned, then the corresponding GPNVM bit is set.
Table 20-28. Get General-purpose NVM Bit Command
Security bits can be set using Set Security Bit command (SSE). Once the security bit is active,
the Fast Flash programming is disabled. No other command can be run. Only an event on the
Erase pin can erase the security bit once the contents of the Flash have been erased.
The AT91SAM7S512 security bit is controlled by the EFC0. To use the Set Security Bit com-
mand, the EFC0 must be selected using the Select EFC command.
Table 20-29. Set Security Bit Command
Once the security bit is set, it is not possible to access FFPI. The only way to erase the security
bit is to erase the Flash.
In order to erase the Flash, the user must perform the following:
Then it is possible to return to FFPI mode and check that Flash is erased.
The commands WPx, EA, xLB, xFB are executed using the current EFC controller. The default
EFC controller is EFC0. The Select EFC command (SEFC) allows selection of the current EFC
controller.
Table 20-30. Select EFC Command
Read/Write
Write
Read
Read/Write
Write
Step
1
2
• Power-off the chip
• Power-on the chip with TST = 0
• Assert Erase during a period of more than 220 ms
• Power-off the chip
Handshake Sequence
Write handshaking
Write handshaking
DR Data
GGPB
Bit Mask
DR Data
SSE
AT91SAM7S Series Preliminary
MODE[3:0]
CMDE
DATA
DATA[15:0]
SEFC
0 = Select EFC0
1 = Select EFC1
141