71M6532D-IGTR/F Maxim Integrated Products, 71M6532D-IGTR/F Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
71M6532D-IGTR/F
Manufacturer Part Number
71M6532D-IGTR/F
Description
IC ENERGY METER 128KB 100-LQFP
Manufacturer
Maxim Integrated Products
Datasheet
1.71M6531D-IMRF.pdf
(120 pages)
Specifications of 71M6532D-IGTR/F
Mounting Style
SMD/SMT
Package / Case
LQFP-100
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
71M6532D-IGTR/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
incremented when the falling edge is observed at the corresponding input signal T0 or T1 (T0 and T1 are
the timer gating inputs derived from certain DIO pins, see Section
cycles to recognize a 1-to-0 event, the maximum input count rate is 1/2 of the clock frequency (CKMPU).
There are no restrictions on the duty cycle, however to ensure proper recognition of the 0 or 1 state, an
input should be stable for at least 1 machine cycle.
Four operating modes can be selected for Timer 0 and Timer 1, as shown in
TMOD Register, shown in
is controlled by the TCON Register, which is shown in
the TCON register start their associated timers when set.
Table 21
Data Sheet 71M6531D/F-71M6532D/F
1.4.7
The 80515 has two 16-bit timer/counter registers: Timer 0 and Timer 1. These registers can be configured
for counter or timer operations.
In timer mode, the register is incremented every 12 MPU clock cycles. In counter mode, the register is
28
S1CON[2]
S1CON[1]
S1CON[0]
PCON[7]
PCON[6:2]
PCON[1]
PCON[0]
M1
0
0
1
1
In Mode 3, TL0 is affected by TR0 and gate control bits and sets the TF0 flag on overflow, while TH0
is affected by the TR1 bit and the TF1 flag is set on overflow.
Bit
Bit
Timers and Counters
specifies the combinations of operation modes allowed for Timer 0 and Timer 1.
M0
RB81
TI1
RI1
SMOD
–
STOP
IDLE
0
1
0
1
Symbol
Symbol
Mode 0
Mode 1
Mode 2
Mode 3
Mode
Table 19: PCON Register Bit Description (SFR 0x87)
© 2005-2010 TERIDIAN Semiconductor Corporation
Table
Table 20: Timers/Counters Mode Description
In Modes A and B, it is the 9
RB81 is the stop bit. Must be cleared by software
Transmit interrupt flag, set by hardware after completion of a serial transfer.
Must be cleared by software.
Receive interrupt flag, set by hardware after completion of a serial reception.
Must be cleared by software.
The SMOD bit doubles the baud rate when set
Not used.
Stops MPU flash access and MPU peripherals including timers and
UARTs when set until an external interrupt is received.
Stops MPU flash access when set until an internal interrupt is received.
22, is used to select the appropriate mode. The timer/counter operation
13-bit Counter/Timer mode with 5 lower bits in the TL0 or TL1 register
and the remaining 8 bits in the TH0 or TH1 register (for Timer 0 and Timer
1, respectively). The 3 high order bits of TL0 and TL1 are held at zero.
16-bit Counter/Timer mode.
8-bit auto-reload Counter/Timer. The reload value is kept in TH0 or
TH1, while TL0 or TL1 is incremented every machine cycle. When TL(x)
overflows, a value from TH(x) is copied to TL(x) (where x = 0 for
counter/timer 0 or 1 for counter/timer 1.
If Timer 1 M1 and M0 bits are set to 1, Timer 1 stops.
If Timer 0 M1 and M0 bits are set to 1, Timer 0 acts as two independent
8-bit Timer/Counters.
Table 23.
th
data bit received. In Mode B, if SM21 is 0,
Function
Function
1.5.7 Digital
Function
Bits TR1 (TCON[6]) and TR0 (TCON[4]) in
I/O). Since it takes 2 machine
Table 20
FDS 6531/6532 005
and
Table
21. The
v1.3