DVK-BTM411 Laird Technologies, DVK-BTM411 Datasheet - Page 24

• Manufacturer Part Number: DVK-BTM411
• Description: BLUETOOTH EVAL BOARD BTM411
• Manufacturer: Laird Technologies
• Type: Transceiverr

Specifications of DVK-BTM411

• Frequency: 2.4GHz
• Wireless Frequency: 2.402 GHz to 2.48 GHz
• Interface Type: UART
• Data Rate: 2.1 Mbps
• Operating Voltage: 3 V to 3.3 V
• Antenna: Multilayer Ceramic Integrated
• Operating Temperature Range: - 30 C to + 70 C
• Output Power: 4 dBm
• Technology/ Type: Development Kit
• For Use With/related Products: BTM411
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: DVK-BTM411

BTM410/411
Bluetooth
AT COMMAND SET
REFERENCE
24 www.lairdtech.com
®
AT Data Module
AT Commands Managing Trusted Devices
AT Commands for Serial Stream Oriented Profiles (SSO)
The Serial Port Profile (SSP) and the Dial-up Networking Profile (DUN) belong to the group of Serial Stream
Oriented profiles (SSO).
When activated, an SSO profile claims one UART for its data stream and assumes all data at the UART to
be transmitted over or received from RF 1:1. Hence, as there is only one UART available on a BTM device,
the UART is not available for other profiles, services or module control purposes.
One approach of managing data and control over UART is to configure local command mode with S531=3.
In this mode, incoming RF data is presented by the asynchronous message RX<string>. Outgoing data is sent
by ATX<string> or ATY<string>.
With this approach it is possible to manage several non-SSO connections (e.g. A2DP, AVRCP) and at
maximum one SSO connection (SSP or DUN). An attempt to connect a second SSO profile while already
one SSO connected will result in Error 65.
Any incoming connection request to an SSO profile will be rejected if one SSO is already connected.
The following section describes AT- commands related to SSO-profiles
1. AT+BTT? {List Trusted Device}
2. AT+BTT
3. AT+BTD<bd_addr> {Remove Trusted Device}
4. AT+BTD* {Remove All Trusted Devices}
5. AT+BTW? {List Cached Trusted Device}
This command is used to list the contents of the trusted device database. The link key is NOT displayed
so the response is as shown below. If the list is empty then just the OK response is sent otherwise an
OK is used to terminate the list. Use the command ATI6 to read the maximum size of the trusted
device database.
Response: <cr,lf>12346789012
<cr,lf>12345678913
<cr,lf>12345678914
<cr,lf>OK<cr,lf>
This command is used to store the cached link key in the non-volatile database. If the database is full
it will respond with an ERROR. If the device is already in the database, then the key is replaced. If the
link key cache is empty, that is, a pairing has not been performed since the device was powered, then
the response will be an ERROR.
Response: <cr,lf>OK<cr,lf>
Or
Response: <cr,lf>ERROR<cr,lf>
This command is used to remove the specified device from the list of trusted devices in the non-volatile
database. If the device is not in the database then the response will still be an OK.
Response: <cr,lf>OK<cr,lf>
This command is used to remove all devices from the trusted device list (TDL) in the non-volatile
database. No confirmation will be asked for. So beware!!!
WARNING: If you make a connection, the link key gets cached in the underlying stack. So if you
subsequently delete the key using AT+BTD* and immediately request a connection to the same device,
then the connection will be established. To ensure this does not happen, send ATZ after the AT+BTD*.
Response: <cr,lf>OK<cr,lf>
This command is used to list the cached trusted device.
Response: <cr,lf>12346789012
<cr,lf>OK<cr,lf>
If the cache is empty the response is as follows.
Response: <cr,lf>OK<cr,lf>
{Add Trusted Device}
Laird Technologies