DVK-BTM411 Laird Technologies, DVK-BTM411 Datasheet - Page 29

• Manufacturer Part Number: DVK-BTM411
• Description: BLUETOOTH EVAL BOARD BTM411
• Manufacturer: Laird Technologies
• Type: Transceiverr

Specifications of DVK-BTM411

• Frequency: 2.4GHz
• Wireless Frequency: 2.402 GHz to 2.48 GHz
• Interface Type: UART
• Data Rate: 2.1 Mbps
• Operating Voltage: 3 V to 3.3 V
• Antenna: Multilayer Ceramic Integrated
• Operating Temperature Range: - 30 C to + 70 C
• Output Power: 4 dBm
• Technology/ Type: Development Kit
• For Use With/related Products: BTM411
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: DVK-BTM411

BTM410/411
Bluetooth
AT COMMAND SET
REFERENCE
29 www.lairdtech.com
®
AT Data Module
Bluetooth Profiles
This section covers S-Registers and AT-Commands that are related to supported Bluetooth Profiles on BTM.
Phase
Preparation
Preparation
7. AT+BTR
8
1. Profile Activation
2. SPP (Serial Port Profile)
The second method is initiated by resetting the device and then ensuring that the text string
“AT+BT&BISM&<cr>” is sent (where <cr> is the carriage return character). There is special code which
looks out for this magic command and terminates the autoconnect cycle if it sees it and confirms to
the host of that fact by sending an “OK” response.
Response: <cr,lf>OK<cr,lf>
This command is used to delete the peer address previously stored using AT+BTR<bd_addr>.
Response: <cr,lf>OK<cr,lf>
AT+BTR? {Read Outgoing Peer Address}
This command is used to display the peer address stored in non-volatile memory, used to put the device
in pure cable replacement mode.
Response: <cr,lf>12346789012
<cr,lf>OK<cr,lf>
If the location is empty the response is as follows.
Response: <cr,lf>00000000000
<cr,lf>OK<cr,lf>
In order to activate available profiles and advertise them to potential client devices, S-Register 102 is
used. Per default, only SPP is activated (value=1). Other supported profiles can be activated by setting
the appropriate Flag in S-Register 102. Once S-Register 102 has been written, the changed value needs
to be saved to non-volatile memory (“AT&W”) and subsequently a reset (“ATZ”) or power cycle is
required. Please note that “AT&W” saves the content of all S Registers to non-volatile memory.
The serial port profile (SPP) is used for serial data transmission with a remote device in both directions.
It behaves like a wireless replacement for a serial cable.
SSP belongs to the group of serial stream oriented profiles (SSO) so please refer to pg. 24 too.
In order to use SPP, the profile must be enabled in S102 (value=1). If it was not enabled earlier, set the
S register accordingly and issue AT&W followed by ATZ.
2.1
SPP example
This section gives an example on how an SPP connection between two Laird BTM devices can
be established. It is assumed that two devices A and B are connected to a terminal program e.g.
Ezurio Terminal on a PC. The example sequence of AT commands is listed in Table 3.9. Figure 3.2
through to Figure 3.5 are presenting appropriate screenshots with Ezurio Terminal.
Dev.
A
B
{Delete Outgoing Peer Address}
AT Command
AT&F*
ATS102=1
AT&W
ATZ
AT&F*
ATS102=1
ATS0=1
AT&W
ATZ
AT+BTP
ATI4
Comment
Restore factory default settings
Enable Serial Port Profile (SPP)
Store settings
Reset
Restore factory default settings
Enable Serial Port Profile (SPP)
Automatic response after one “RING”
Store settings
Reset
Make device temporary connectable and discoverable
Query Bluetooth device address of local device <BdAddr_DevB>
Laird Technologies