AT86RF212-ZU Atmel, AT86RF212-ZU Datasheet - Page 92

• Manufacturer Part Number: AT86RF212-ZU
• Description: IC TXRX ZIGBE/802.15.4/ISM 32QFN
• Manufacturer: Atmel

Specifications of AT86RF212-ZU

• Frequency: 700MHz, 800MHz, 900MHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, ISM
• Applications: ISM, ZigBee™
• Power - Output: 10dBm
• Sensitivity: -110dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 9.2mA
• Current - Transmitting: 25mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 769 MHz to 935 MHz
• Interface Type: SPI
• Noise Figure: 7 dB
• Output Power: 21 dB
• Operating Supply Voltage: 1.8 V, 3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 25 mA
• Minimum Operating Temperature: - 40 C
• Modulation: OQPSK
• Protocol Supported: 802.15.4
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

7 Module Description
7.1 Physical Layer Modes
7.1.1 Spreading, Modulation, and Pulse Shaping
92
AT86RF212
The AT86RF212 supports various physical layer (PHY) modes independent of the RF
channel selection. Symbol mapping along with chip spreading, modulation, and pulse
shaping is part of the digital base band processor, see Figure 7-1.
Figure 7-1. Base Band Transmitter Architecture
The combination of spreading, modulation, and pulse shaping are restricted to several
combinations as shown in Table 7-1.
The AT86RF212 is fully compliant to the IEEE 802.15.4 low data rate modes of 20
kbit/s or 40 kbit/s, employing binary phase-shift keying (BPSK) and spreading with a
fixed chip rate of 300 kchip/s or 600 kchip/s, respectively. The symbol rate is 20
ksymbol/s or 40 ksymbol/s, respectively. In both cases, pulse shaping is approximating
a raised cosine filter with roll-off factor 1.0 (RC-1.0).
For optional data rates according to IEEE 802.15.4-2006, offset quadrature phase-shift
keying (O-QPSK) is supported by the AT86RF212 with a fixed chip rate of either 400
kchip/s or 1000 kchip/s.
At a chip rate of 400 kchip/s, pulse shaping is always a combination of both, half-sine
shaping (SIN) and raised cosine filtering with roll-off factor 0.2 (RC-0.2) according to
IEEE 802.15.4-2006 for the 868.3 MHz band. At a chip rate of 1000 kchip/s, pulse
shaping is either half-sine filtering (SIN) as specified in IEEE 802.15.4-2006 [2], or,
alternatively, raised cosine filtering with roll-off factor 0.8 (RC-0.8) as specified in IEEE
802.15.4c-2009 [3].
For O-QPSK, the AT86RF212 supports spreading according to IEEE 802.15.4-2006
with data rates of either 100 kbit/s or 250 kbit/s depending on the chip rate, leading to a
symbol rate of either 25 ksymbol/s or 62.5 ksymbol/s, respectively.
Additionally, the AT86RF212 supports two more spreading codes for O-QPSK with
shortened code lengths. This leads to higher but non IEEE 802.15.4-2006 compliant
data rates during the PSDU part of the frame with 200, 400, 500, and 1000 kbit/s. The
proprietary High Data Rate Modes are outlined in more detail in section 7.1.4.
Table 7-1. Modulation and Pulse Shaping
Modulation
BPSK
O-QPSK
Chip Rate
[kchip/s]
1000
300
600
400
Supported Data
Header [kbit/s]
Rate for PPDU
100
250
20
40
Supported Data
Rates for PSDU
250, 500, 1000
100, 200, 400
[kbit/s]
20
40
8168C-MCU Wireless-02/10
Pulse Shaping
RC-1.0
RC-1.0
SIN and RC-0.2
SIN or RC-0.8