MC13212 Freescale Semiconductor, MC13212 Datasheet - Page 20
![IC TXRX RF 2.4GHZ FLSH 32K 71LGA](/photos/14/22/142235/mc13212_sml.jpg)
MC13212
Manufacturer Part Number
MC13212
Description
IC TXRX RF 2.4GHZ FLSH 32K 71LGA
Manufacturer
Freescale Semiconductor
Series
MC1321xr
Datasheet
1.1321XCSK-BDM.pdf
(70 pages)
Specifications of MC13212
Frequency
2.4GHz
Data Rate - Maximum
250kbps
Modulation Or Protocol
802.15.4 Zigbee
Applications
General Purpose
Power - Output
3dBm
Sensitivity
-92dBm
Voltage - Supply
1.8 V ~ 3.6 V
Current - Receiving
42mA
Current - Transmitting
35mA
Data Interface
PCB, Surface Mount
Memory Size
32kB Flash, 2kB RAM
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
71-LGA
Mounting Style
SMD/SMT
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC13212
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
MC13212R2
Manufacturer:
FREESCALE
Quantity:
340
4.6.2
The MCU directs the 802.15.4 modem, checks its status, and reads/writes data to the device through the
4-wire SPI port. The transceiver operates as a SPI slave device only. A transaction between the host and
the 802.15.4 modem occurs as multiple 8-bit bursts on the SPI. The modem SPI signals are:
Although the SPI port is fully static, internal memory, timer and interrupt arbiters require an internal clock
(CLK
registers and memory.
4.6.2.1
The SPI port of the MCU transfers data in bursts of 8 bits with most significant bit (MSB) first. The master
(MCU) can send a byte to the slave (transceiver) on the MOSI line and the slave can send a byte to the
master on the MISO line. Although an 802.15.4 modem transaction is three or more SPI bursts long, the
timing of a single SPI burst is shown in
because the modem is limited by this number.
20
1. Chip Enable (CE) - A transaction on the SPI port is framed by the active low CE input signal. A
2. SPI Clock (SPICLK) - The host drives the SPICLK input to the 802.15.4 modem. Data is clocked
3. Master Out/Slave In (MOSI) - Incoming data from the host is presented on the MOSI input.
4. Master In/Slave Out (MISO) - The 802.15.4 modem presents data to the master on the MISO
core
SPICLK
CE
MISO
MOSI
transaction is a minimum of 3 SPI bursts and can extend to a greater number of bursts.
into the master or slave on the leading (rising) edge of the return-to-zero SPICLK and data out
changes state on the trailing (falling) edge of SPICLK.
output.
), derived from the crystal reference oscillator, to communicate from the SPI registers to internal
Serial Peripheral Interface (SPI)
SPI Burst Operation
For the MCU, the SPI clock format is the clock phase control bit CPHA = 0
and the clock polarity control bit CPOL = 0.
Valid
1
Valid
Figure 10. SPI Single Burst Timing Diagram
2
MC13211/212/213 Technical Data, Rev. 1.8
Figure
3
10. The maximum SPI clock rate is 8 Mhz from the MCU
NOTE
4
SPI Burst
5
6
7
Freescale Semiconductor
8