ATA8742-PXQW Atmel, ATA8742-PXQW Datasheet - Page 85

• Manufacturer Part Number: ATA8742-PXQW
• Description: MCU W/TRANSMITTER ASK/FSK 24QFN
• Manufacturer: Atmel

Specifications of ATA8742-PXQW

• Frequency: 433MHz
• Applications: Home Automation, Remote Sensing, RKE
• Modulation Or Protocol: ASK, FSK
• Data Rate - Maximum: 32 kBit/s
• Power - Output: 7.5dBm
• Current - Transmitting: 9.8mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Memory Size: 4kB Flash, 256B EEPROM, 256B SRAM
• Voltage - Supply: 2 V ~ 4 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 24-VQFN Exposed Pad, 24-HVQFN, 24-SQFN, 24-DHVQFN
• Processor Series: ATA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 4 KB
• Data Ram Size: 256 B
• Interface Type: SPI, USI
• Maximum Clock Frequency: 8.1 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ATASTK512-EK1-IND
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Details

9151A–INDCO–07/09
• Port B, Bit 3 – RESET/dW/PCINT11
RESET: External Reset input is active low and enabled by unprogramming (“1”) the RSTDISBL
Fuse. Pullup is activated and output driver and digital input are deactivated when the pin is used
as the RESET pin.
dW: When the debugWIRE Enable (DWEN) Fuse is programmed and Lock bits are unpro-
grammed, the debugWIRE system within the target device is activated. The RESET port pin is
configured as a wire-AND (open-drain) bi-directional I/O pin with pull-up enabled and becomes
the communication gateway between target and emulator.
PCINT11: Pin Change Interrupt source 11. The PB3 pin can serve as an external interrupt
source for pin change interrupt 1.
Table 19-8 on page 85
overriding signals shown in
Table 19-8.
1.
2.
Signal
Name
PUOE
PUOV
DDOE
DDOV
PVOE
PVOV
PTOE
DIEOE
DIEOV
DI
AIO
RSTDISBL is 1 when the Fuse is “0” (Programmed).
DebugWIRE is enabled when DWEN Fuse is programmed and Lock bits are unprogrammed.
PB3/
PCINT11
RSTDISBL
1
RSTDISBL
DEBUGWIRE_ENABLE
Transmit
RSTDISBL
0
0
RSTDISBL
PCINT11 • PCIE1
DEBUGWIRE_ENABLE
PCINT11 • PCIE1)
dW/PCINT11 Input
Overriding Signals for Alternate Functions in PB3..PB2
RESET/dW/
(1)
(1)
(1)
(1)
and
+ DEBUGWIRE_ENABLE
+ DEBUGWIRE_ENABLE
+ DEBUGWIRE_ENABLE
+ DEBUGWIRE_ENABLE
Figure 19-5 on page
Table 19-9 on page 86
(2)
(2)
+ (RSTDISBL
• debugWire
(2)
(2)
(2)
(2)
(1)
78.
+
•
relate the alternate functions of Port B to the
PB2/INT0/OC0A/CKOUT/PCINT10
CKOUT
0
CKOUT
1'b1
CKOUT + OC0A enable
CKOUT • System Clock + CKOUT • OC0A
0
PCINT10 • PCIE1 + INT0
PCINT10 • PCIE1 + INT0
INT0/PCINT10 Input
ATA8742
85