XR16L580IM-F Exar Corporation, XR16L580IM-F Datasheet - Page 16
![IC UART FIFO 16B 48TQFP](/photos/16/10/161019/tqfp-48_sml.jpg)
XR16L580IM-F
Manufacturer Part Number
XR16L580IM-F
Description
IC UART FIFO 16B 48TQFP
Manufacturer
Exar Corporation
Datasheet
1.XR16L580IL24TR-F.pdf
(52 pages)
Specifications of XR16L580IM-F
Number Of Channels
1, UART
Package / Case
48-TQFP
Features
*
Fifo's
16 Byte
Protocol
RS232, RS422
Voltage - Supply
2.25 V ~ 5.5 V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Modem Control
Yes
With Cmos
Yes
Mounting Type
Surface Mount
Data Rate
3.125 Mbps
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.25 V
Supply Current
2 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
No. Of Channels
1
Uart Features
Selectable RX And TX FIFO Trigger Levels, Automatic Software Flow Control, Complete Modem Interface
Supply Voltage Range
2.25V To 5.5V
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XR16L580IM-F
Manufacturer:
Exar Corporation
Quantity:
10 000
Part Number:
XR16L580IM-F
Manufacturer:
EXAR/艾科嘉
Quantity:
20 000
XR16L580
SMALLEST 2.25V TO 5.5V UART WITH 16-BYTE FIFO AND POWERSAVE
This feature is not available in the 24-QFN package since it does not have the RTS# pin.
Automatic RTS hardware flow control is used to prevent data overrun to the local receiver FIFO. The RTS#
output is used to request remote unit to suspend/resume data transmission. The auto RTS flow control
features is enabled to fit specific application requirement (see
•
•
If using the Auto RTS interrupt:
•
The L580 has a new feature that provides flow control trigger hysteresis while maintaining compatibility with
the ST16C550 UART. With the Auto RTS function enabled, an interrupt is generated when the receive FIFO
reaches the programmed RX trigger level. The RTS# pin will not be forced to a logic 1 (RTS off), until the
receive FIFO reaches one trigger level above the programmed trigger level in the trigger table (
RTS# pin will return to a logic 0 after the RX FIFO is unloaded to one trigger level lower than the programmed
trigger level. This is described in
accept data until the receive FIFO gets full. The Auto RTS function is initiated when the RTS# output pin is
asserted to a logic 0 (RTS On).
This feature is not available in the 24-QFN package since it does not have the CTS# pin.
Automatic CTS flow control is used to prevent data overrun to the remote receiver FIFO. The CTS# input is
monitored to suspend/restart the local transmitter. The auto CTS flow control feature is selected to fit specific
application requirement (see
•
If using the Auto CTS interrupt:
•
2.12
2.13
2.14
Enable auto RTS flow control using EFR bit-6.
The auto RTS function must be started by asserting RTS# output pin (MCR bit-1 to logic 1 after it is enabled).
Enable RTS interrupt through IER bit-6 (after setting EFR bit-4). The UART issues an interrupt when the
RTS# pin makes a transition from low to high: ISR bit-5 will be set to logic 1.
Enable auto CTS flow control using EFR bit-7.
Enable CTS interrupt through IER bit-7 (after setting EFR bit-4). The UART issues an interrupt when the
CTS# pin is de-asserted (HIGH): ISR bit-5 will be set to 1, and UART will suspend transmission as soon as
the stop bit of the character in process is shifted out. Transmission is resumed after the CTS# input is re-
asserted (LOW), indicating more data may be sent.
Auto RTS Hysteresis
Auto CTS Flow Control
Auto RTS (Hardware) Flow Control
Figure 12
Figure 12
):
. Under the above described conditions, the L580 will continue to
16
Figure 12
):
Table 8
REV. 1.4.1
). The