LIS302DLH STMicroelectronics, LIS302DLH Datasheet - Page 17

• Manufacturer Part Number: LIS302DLH
• Description: SENSOR ACCELEROMETER 3AXIS 14LGA
• Manufacturer: STMicroelectronics

Specifications of LIS302DLH

• Featured Product: STM32 Cortex-M3 Companion Products
• Axis: X, Y, Z
• Acceleration Range: ±2.3g, 9.2g
• Sensitivity: 18mg/digit, 72mg/digit
• Voltage - Supply: 2.16 V ~ 3.6 V
• Output Type: Digital
• Bandwidth: 100Hz ~ 400Hz Selectable
• Interface: I²C, SPI
• Mounting Type: Surface Mount
• Package / Case: 14-LGA
• Package Type: LGA
• Operating Supply Voltage (min): 2.16V
• Operating Supply Voltage (typ): 2.5V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Product Depth (mm): 3mm
• Product Height (mm): 0.92mm
• Product Length (mm): 5mm
• Mounting: Surface Mount
• Pin Count: 14
• Sensing Axis: Triple
• Acceleration: 2 g, 4 g, 8 g
• Digital Output - Number Of Bits: 16 bit
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.16 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Digital Output - Bus Interface: I2C, SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-10052

LIS302DLH
5
5.1
Digital interfaces
The registers embedded inside the LIS302DLH may be accessed through both the I
SPI serial interfaces. The latter may be SW configured to operate either in 3-wire or 4-wire
interface mode.
The serial interfaces are mapped onto the same pads. To select/exploit the I
line must be tied high (i.e. connected to Vdd_IO).
Table 8.
I
The LIS302DLH I
content can also be read back.
The relevant I
Table 9.
There are two signals associated with the I
DAta line (SDA). The latter is a bidirectional line used for sending and receiving the data
to/from the interface. Both the lines are connected to Vdd_IO through a pull-up resistor
embedded inside the LIS302DLH. When the bus is free both the lines are high.
The I
normal mode.
2
C serial interface
Transmitter
Pin name
2
Receiver
C interface is compliant with fast mode (400 kHz) I
Master
Term
Slave
SDO
SDO
SPC
SDA
SCL
SA0
SDI
CS
Serial interface pin description
Serial interface pin description
2
C terminology is given in the table below.
2
C is a bus slave. The I
SPI enable
I
I
SPI serial port clock (SPC)
I
SPI serial data input (SDI)
3-wire interface serial data output (SDO)
I
SPI serial data output (SDO)
The device which sends data to the bus
The device which receives data from the bus
The device which initiates a transfer, generates clock signals and terminates a
transfer
The device addressed by the master
2
2
2
2
C/SPI mode selection (1: I
C serial clock (SCL)
C serial data (SDA)
C less significant bit of the device address (SA0)
Doc ID 15797 Rev 1
2
C is employed to write data into registers whose
2
C bus: the serial clock line (SCL) and the Serial
2
C mode; 0: SPI enabled)
Pin description
Description
2
C standards as well as with the
Digital interfaces
2
C interface, CS
2
C and
17/37