LPC2119FBD64 NXP Semiconductors, LPC2119FBD64 Datasheet - Page 2

• Manufacturer Part Number: LPC2119FBD64
• Description: 16/32BIT MCU ARM7, 128K FLASH, 64LQFP
• Manufacturer: NXP Semiconductors

Specifications of LPC2119FBD64

• No. Of I/o's: 46
• Ram Memory Size: 16KB
• Cpu Speed: 60MHz
• No. Of Timers: 2
• No. Of Pwm Channels: 6
• Digital Ic Case: RoHS Compliant
• Core Size: 32bit
• Program Memory Size: 128KB
• Oscillator Type: External Only
• Controller Family/series: LPC21xx
• Rohs Compliant: Yes
• Data Bus Width: 16 bit, 32 bit
• Program Memory Type: Flash
• Data Ram Size: 16 KB
• Interface Type: CAN, I2C, JTAG, SPI, SSP, UART
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 46
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: LQFP
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• Lead Free Status / Rohs Status: Details

NXP Semiconductors
3. Ordering information
Product data sheet
LPC2109_2119_2129_6
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Table 1.
Type number
LPC2109FBD64/00
LPC2109FBD64/01
LPC2119FBD64
LPC2119FBD64/00
LPC2119FBD64/01
64/128/256 kB on-chip flash program memory. 128-bit wide interface/accelerator
enables high speed 60 MHz operation.
In-System Programming (ISP) and In-Application Programming (IAP) via on-chip
bootloader software. Flash programming takes 1 ms per 512 B line. Single sector or
full chip erase takes 400 ms.
EmbeddedICE-RT interface enables breakpoints and watch points. Interrupt service
routines can continue to execute while the foreground task is debugged with the
on-chip RealMonitor software.
Embedded Trace Macrocell (ETM) enables non-intrusive high speed real-time tracing
of instruction execution.
Two interconnected CAN interfaces (one for LPC2109) with advanced acceptance
filters.
Four-channel 10-bit A/D converter with conversion time as low as 2.44 s.
Multiple serial interfaces including two UARTs (16C550), Fast I
two SPIs.
60 MHz maximum CPU clock available from programmable on-chip Phase-Locked
Loop with settling time of 100 s.
Vectored Interrupt Controller with configurable priorities and vector addresses.
Two 32-bit timers (with four capture and four compare channels), PWM unit (six
outputs), Real-Time Clock (RTC) and watchdog.
Up to forty-six 5 V tolerant general purpose I/O pins. Up to nine edge or level sensitive
external interrupt pins available.
On-chip crystal oscillator with an operating range of 1 MHz to 30 MHz.
Two low power modes, Idle and Power-down.
Processor wake-up from Power-down mode via external interrupt.
Individual enable/disable of peripheral functions for power optimization.
Dual power supply:
N
N
CPU operating voltage range of 1.65 V to 1.95 V (1.8 V
I/O power supply range of 3.0 V to 3.6 V (3.3 V
Ordering information
Package
Name
LQFP64
LQFP64
LQFP64
LQFP64
LQFP64
Rev. 06 — 10 December 2007
Description
plastic low profile quad flat package; 64 leads;
body 10
plastic low profile quad flat package; 64 leads;
body 10
plastic low profile quad flat package; 64 leads;
body 10
plastic low profile quad flat package; 64 leads;
body 10
plastic low profile quad flat package; 64 leads;
body 10
10
10
10
10
10
1.4 mm
1.4 mm
1.4 mm
1.4 mm
1.4 mm
LPC2109/2119/2129
Single-chip 16/32-bit microcontrollers
10 %) with 5 V tolerant I/O pads.
0.15 V).
2
C-bus (400 kbit/s) and
© NXP B.V. 2007. All rights reserved.
Version
SOT314-2
SOT314-2
SOT314-2
SOT314-2
SOT314-2
2 of 44