TLA21000 Red Lion Controls, TLA21000 Datasheet - Page 9

• Manufacturer Part Number: TLA21000
• Description: Form-C Limit Relay W/1 Alarm
• Manufacturer: Red Lion Controls
• Type: Temperaturer

Specifications of TLA21000

• Brand/series: TLA Series
• Contact Form: SPST/SPDT
• Dimensions: 49.5mmW×49.5mmH×115.3mmD
• Enclosure Rating: IP65
• Input Type: RTD/Thermocouple
• Ip Rating: IP65
• Memory: EEPROM
• Mounting Type: Panel
• Number Of Outputs: 1
• Output Type: Relay
• Power, Rating: 8 VA
• Primary Type: Controller
• Special Features: EEPROM
• Standards: cURus, CE, FM
• Temperature, Ambient: 0 to +50 °C (Max.)
• Termination: Screw
• Voltage, Rating: 120⁄240 VAC
• Voltage, Supply: 85 to 250 VAC
• Panel Cutout: 1.77" × 1.77" (1⁄16 DIN)
• Power Requirements: 85-250 VAC
• Sealing: NEMA 4X/IP65
• Operating Temperature: 0°C to +50°C
• Lead Free Status / Rohs Status: RoHS Compliant part

C
USER PARAMETER VALUE CHART
TLA Number _____________
CodE
ONFIGURE
MNEMONIC
MNEMONIC
MNEMONIC
1-IN
2-OP
tYPE
SCAL
dCPt
FLtr
SHFt
SPLO
SPHI
LiAc
pass
sp
aL-1
AL-2
DISPLAY
Output Parameters
Input Parameters
Factory service function
code
PARAMETER
Input Sensor Type
Temperature Scale Units
Temperature Resolution
Digital Filtering
Input Offset
Limit Setpoint Lower Limit
Limit Setpoint Upper Limit
PARAMETER
Limit Output Trip Action
PARAMETER
Password
Limit Setpoint
Alarm 1 Value
Alarm 2 Value
PARAMETER
M
ODULE
48 - Calibrate instrument
66 - Reset parameters to factory
settings
77 (twice in succession) -
Reset TLA calibration to nominal
values
9 - F
USER SETTING
USER SETTING
USER SETTING
ACTORY
RANGE
S
9
ERVICE
TLA calibration. Refer to the Calibration section for details.
Entering code 66 restores all parameters to factory settings. The
unit indicates the operation after the P button is pressed, by
displaying “rSEt” in the lower display momentarily.
Caution: this operation erases the TLA calibration values and
defaults the values to nominal settings. Reading errors of ±10%
may result. Do not perform this operation unless the TLA has lost
calibration. Loss of calibration is signaled by an “E-CL” error
flag at power-up. To clear this flag, perform calibration procedure
as noted in the Calibration section. Alternatively, “stepping” through
one of the calibration procedures clears the error flag, but does NOT
validate the calibration accuracy in any manner.
MNEMONIC
MNEMONIC
3-LC
4-AL
PASS
AL
FPrS
Act1
rst1
stb1
aL-1
Act2
rst2
stb2
aL-2
aHYS
Lockout Parameters
Configure Alarm Parameters
O
PERATIONS
DESCRIPTION/ COMMENTS
PARAMETER
Password
Alarm(s) Access Level
Front Panel Reset
PARAMETER
Alarm 1 Action Mode
Alarm 1 Reset Mode
Alarm 1 Standby Enabled
Alarm 1 Value
Alarm 2 Action Mode
Alarm 2 Reset Mode
Alarm 2 Standby Enabled
Alarm 2 Value
Alarm Hysteresis Value
(9-FS)
USER SETTING
USER SETTING