A1360LKTTN-T Allegro Microsystems Inc, A1360LKTTN-T Datasheet - Page 5

• Manufacturer Part Number: A1360LKTTN-T
• Description: IC,HALL-EFFECT SENSOR,SINGLE-ENDED,BICMOS,SIP,4PIN,PLASTIC
• Manufacturer: Allegro Microsystems Inc
• Type: Linear - Unipolar, Bipolarr

Specifications of A1360LKTTN-T

• Sensing Range: 0.7mV/G ~ 1.4mV/G
• Voltage - Supply: 4.5 V ~ 5.5 V
• Current - Supply: 12mA
• Current - Output (max): 10mA
• Output Type: Analog, Ratiometric
• Features: Programmable
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 4-SIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 620-1233-2

A1360, A1361,
and A1362
OPERATING CHARACTERISTICS (continued) valid over full operating temperature range, T
Drift Characteristics
Quiescent Voltage Output Drift
Through Temperature Range
Sensitivity Drift Due to Package
Hysteresis
1
2
3
gauss levels required for testing A1360 V
4
floor attenuates proportionate to the filter capacitance (and device bandwidth).
5
6
7
8
addressed before V
9
10
11
including V
12
13
Step
14
15
16
Sens(max). See Characteristic Definitions section. Sensitivity may drift by an additional ±2% over the lifetime of this product.
17
18
devices. These linearity ranges are only valid within the operating output range of the device. The operating output range is confined to the region between the output clamps.
Linearity may shift by up to +/- 1 % over the lifetime of this product.
19
20
21
See Characteristic Definitions section.
f
V
Noise is dependent on the sensitivity of the device and the filter capacitance. An 8 mV peak-to-peak noise floor exists that is independent of device sensitivity. This noise
Unit of measure (phase degrees) in reference to the magnetic input signal.
High-to-low transition of output voltage is a function of external load components and device sensitivity.
Raw device characteristic values before any programming.
V
Bits for selecting between V
C
V
V
Step size is larger than required, in order to provide for manufacturing spread. See Characteristic Definitions section.
Sens(max) is the value available with all programming fuses blown (maximum programming code set). Sens range is the total range from Sens
Programmed at 150°C and calculated relative to 25°C.
Non-ideal behavior in the programming DAC can cause the step size at each significant bit rollover code to be greater than twice the maximum specified value of
Overall programming value accuracy. See Characteristic Definitions section.
Sens guaranteed by design.
Linearity is only guaranteed for output voltage ranges of ±2 V from the quiescent output for bidirectional devices and +2 V from the quiescent output for unidirectional
Symmetry error is only valid for bidirectional devices. Symmetry may shift by up to ±1% over the lifetime of this product.
Percent change from actual value at V
Percent change from actual value at V
CLP
OUT(Q)UNIinit
OUT(Q)
varies up to approximately ±20% over the full operating ambient temperature range, T
OUT(Q)
VOUT(Q)
voltages are production-tested, with the sole exception of the A1360 V
(max) is the value available with all programming fuses blown (maximum programming code set). The V
guaranteed by design.
Characteristic
OUT(Q)
1
or Step
typically starts below the lower clamp voltage, V
(max). See Characteristic Definitions section. Quiescent Voltage Output may drift by an additional ±10 mV over the lifetime of this product.
OUT(Q)UNI
SENS
.
can be measured above V
OUT(Q)UNI
1
and V
CC
CC
CLP(HIGH)
∆Sens
∆V
Symbol
= 5 V, for a given temperature, over the guaranteed supply voltage operating range.
= 5 V, T
Adjustable Bandwidth (50 kHz Maximum) and Analog Output
Low-Noise Programmable Linear Hall Effect Sensor ICs with
OUT(Q)BI
OUT(Q)
PKG
make production testing impractical).
A
= 25°C, over the guaranteed supply voltage operating range.
programming ranges.
T
CLP(LOW)
A1360
A1361
A1362
A1360
A1361
A1362
A
= 25°C, after temperature cycling
CLP(LOW)
.
V
V
OUT(Q)
OUT(Q)
. When programming the fine quiescent duty cycle for this parameter, several codes may need to be
Test Conditions
= 2.5 V; Sens = Sens(min)
= 2.5 V; Sens = Sens(max)
CLP(HIGH)
, which is guaranteed by design (the low sensitivity and corresponding high
A
, and process.
A
; C
BYPASS
OUT(Q)
–160
Min.
– 35
–20
–20
–60
–50
= 0.1 μF, V
–
range is the total range from V
115 Northeast Cutoff
1.508.853.5000; www.allegromicro.com
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 U.S.A.
CC
Typ.
< ±1
= 5 V, unless otherwise specifi ed
–
–
–
–
–
–
init
up to and including
OUT(Q)init
Max.
160
20
20
60
35
50
–
up to and
Units
mV
mV
mV
mV
mV
mV
%
5