ADF7021-VBCPZ-RL Analog Devices Inc, ADF7021-VBCPZ-RL Datasheet - Page 21
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADF7021-VBCPZ-RL
Manufacturer Part Number
ADF7021-VBCPZ-RL
Description
Narrow Band Transceiver 433/868/900 MHz
Manufacturer
Analog Devices Inc
Datasheet
1.EVAL-ADF7021-VDB2Z.pdf
(60 pages)
Specifications of ADF7021-VBCPZ-RL
Frequency
80MHz ~ 960MHz
Data Rate - Maximum
24 kbps
Modulation Or Protocol
FSK
Applications
ISM
Power - Output
13dBm
Sensitivity
-125dBm
Voltage - Supply
2.3 V ~ 3.6 V
Current - Receiving
21.7mA
Current - Transmitting
27.1mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
48-VFQFN, CSP Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
FREQUENCY SYNTHESIZER
REFERENCE INPUT
The on-board crystal oscillator circuitry (see Figure 32) can use
a quartz crystal as the PLL reference. A quartz crystal with a fre-
quency tolerance of ≤10 ppm for narrow-band applications is
recommended. It is possible to use a quartz crystal with >10 ppm
tolerance, but compensation for the frequency error of the crystal
is necessary to comply with the absolute frequency error speci-
fications of narrow-band regulations (for example, ARIB STD-T67
and ETSI EN 300 220).
The oscillator circuit is enabled by setting Bit DB12 in Register 1
high. It is enabled by default on power-up and is disabled by
bringing CE low. Errors in the crystal can be corrected using
the automatic frequency control (AFC) feature or by adjusting
the fractional-N value (see the N Counter section).
Two parallel resonant capacitors are required for oscillation at
the correct frequency. Their values are dependent on the crystal
specification. The resonant capacitors should be selected to
ensure that the series value of capacitance added to the PCB
track capacitance adds up to the specified load capacitance of
the crystal, usually 12 pF to 20 pF. Track capacitance values vary
from 2 pF to 5 pF, depending on board layout. When possible,
choose capacitors that have a very low temperature coefficient
to ensure stable frequency operation over all conditions.
Using a TCXO Reference
A single-ended reference (TCXO, VCXO, or OCXO) can also be
used with the ADF7021-V. This is recommended for applications
that have absolute frequency accuracy requirements of <10 ppm,
such as applications requiring compliance with ARIB STD-T67
or ETSI EN 300 220. The following are two options for inter-
facing the ADF7021-V to an external reference oscillator.
•
•
Programmable Crystal Bias Current
Bias current in the oscillator circuit can be configured from
20 μA to 35 μA by writing to the XTAL_BIAS bits (Register 1,
Bits[DB14:DB13]). Increasing the bias current allows the crystal
oscillator to power up faster.
An oscillator with CMOS output levels can be applied to
OSC2. The internal oscillator circuit should be disabled by
setting Bit DB12 in Register 1 low.
An oscillator with 0.8 V p-p levels can be ac-coupled through
a 22 pF capacitor into OSC1. The internal oscillator circuit
should be enabled by setting Bit DB12 in Register 1 high.
Figure 32. Crystal Oscillator Circuit on the ADF7021-V
OSC1
CP2
OSC2
CP1
Rev. 0 | Page 21 of 60
CLKOUT Divider and Buffer
The CLKOUT circuit takes the reference clock signal from the
oscillator section, shown in Figure 32, and supplies a divided-
down, 50:50 mark/space signal to the CLKOUT pin. The
CLKOUT signal is inverted with respect to the reference clock.
An even divide from 2 to 30 is available; this divide number is
set in Register 1, Bits[DB10:DB7]. On power-up, the CLKOUT
defaults to divide-by-8.
To disable CLKOUT, set the divide number to 0. The output
buffer can drive a load of up to 20 pF with a 10% rise time at
4.8 MHz. Faster edges can result in some spurious feedthrough
to the output. A series resistor (1 kΩ) can be used to slow the
clock edges to reduce these spurs at the CLKOUT frequency.
R Counter
The 3-bit R counter divides the reference input frequency by an
integer from 1 to 7. The divided-down signal is presented as the
reference clock to the phase frequency detector (PFD). The
divide ratio is set in Register 1, Bits[DB6:DB4]. Maximizing the
PFD frequency reduces the N value. This reduces the noise multi-
plied at a rate of 20 log(N) to the output and reduces occurrences
of spurious components.
Register 1 defaults to R = 1 on power-up.
Loop Filter
The loop filter integrates the current pulses from the charge
pump to form a voltage that tunes the output of the VCO to the
desired frequency. It also attenuates spurious levels generated by
the PLL. A typical loop filter design is shown in Figure 34.
The loop should be designed so that the loop bandwidth (LBW) is
approximately 6 kHz. This provides a good compromise between
in-band phase noise and out-of-band spurious rejection. Widening
the LBW excessively reduces the time spent jumping between
frequencies, but it can cause insufficient spurious attenuation.
The loop filter design on the EVAL-ADF7021-VDBxZ should
be used for optimum performance.
PFD (Hz) = XTAL/R
OSC1
PUMP OUT
CHARGE
Figure 34. Typical Loop Filter Configuration
DIVIDER
1 TO 15
Figure 33. CLKOUT Stage
÷2
V
DD
VCO
CLKOUT
CLKOUT
ENABLE BIT
ADF7021-V