DSPIC30F2010-20E/MM Microchip Technology, DSPIC30F2010-20E/MM Datasheet - Page 86
![IC,DSP,16-BIT,CMOS,LLCC,28PIN,PLASTIC](/photos/6/81/68120/150-28-qfn_sml.jpg)
DSPIC30F2010-20E/MM
Manufacturer Part Number
DSPIC30F2010-20E/MM
Description
IC,DSP,16-BIT,CMOS,LLCC,28PIN,PLASTIC
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20IP.pdf
(26 pages)
2.DSPIC30F2010-20ISO.pdf
(202 pages)
3.DSPIC30F2010-20ISO.pdf
(6 pages)
4.DSPIC30F2010-20ISO.pdf
(26 pages)
Specifications of DSPIC30F2010-20E/MM
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
20
Program Memory Size
12KB (4K x 24)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 6x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
28-QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F2010-20E/MM
Manufacturer:
Microchip Technology
Quantity:
135
Complementary mode by default upon a device Reset.
dsPIC30F2010
14.5.1
The four PWM duty cycle registers are double-buffered
to allow glitchless updates of the PWM outputs. For
each duty cycle, there is a duty cycle register that is
accessible by the user and a second duty cycle register
that holds the actual compare value used in the present
PWM period.
For edge-aligned PWM output, a new duty cycle value
will be updated whenever a match with the PTPER reg-
ister occurs and PTMR is reset. The contents of the
duty cycle buffers are automatically loaded into the
duty cycle registers when the PWM time base is dis-
abled (PTEN = 0) and the UDIS bit is cleared in
PWMCON2.
When the PWM time base is in the Up/Down Counting
mode, new duty cycle values are updated when the
value of the PTMR register is zero and the PWM time
base begins to count upwards. The contents of the duty
cycle buffers are automatically loaded into the duty
cycle registers when the PWM time base is disabled
(PTEN = 0).
When the PWM time base is in the Up/Down Counting
mode with double updates, new duty cycle values are
updated when the value of the PTMR register is zero,
and when the value of the PTMR register matches the
value in the PTPER register. The contents of the duty
cycle buffers are automatically loaded into the duty
cycle registers when the PWM time base is disabled
(PTEN = 0).
14.6
In the Complementary mode of operation, each pair of
PWM outputs is obtained by a complementary PWM
signal. A dead time may be optionally inserted during
device switching, when both outputs are inactive for a
short period (Refer to
Generators”).
In Complementary mode, the duty cycle comparison
units are assigned to the PWM outputs as follows:
• PDC1 register controls PWM1H/PWM1L outputs
• PDC2 register controls PWM2H/PWM2L outputs
• PDC3 register controls PWM3H/PWM3L outputs
The Complementary mode is selected for each PWM
I/O pin pair by clearing the appropriate PMODx bit in the
PWMCON1 SFR. The PWM I/O pins are set to
DS70118J-page 86
Complementary PWM Operation
DUTY CYCLE REGISTER BUFFERS
Section 14.7 “Dead-Time
14.7
Dead-time generation may be provided when any of
the PWM I/O pin pairs are operating in the Comple-
mentary Output mode. The PWM outputs use Push-
Pull drive circuits. Due to the inability of the power out-
put devices to switch instantaneously, some amount of
time must be provided between the turn off event of one
PWM output in a complementary pair and the turn on
event of the other transistor.
14.7.1
Each complementary output pair for the PWM module
has a 6-bit down counter that is used to produce the
dead-time insertion. As shown in
dead-time unit has a rising and falling edge detector
connected to the duty cycle comparison output.
14.7.2
The amount of dead time provided by the dead-time
unit is selected by specifying the input clock prescaler
value and a 6-bit unsigned value.
Four input clock prescaler selections have been pro-
vided to allow a suitable range of dead times, based on
the device operating frequency. The dead-time clock
prescaler value is selected using the DTAPS<1:0> and
DTBPS<1:0> control bits in the DTCON1 SFR. One of
four clock prescaler options (T
is selected for the dead-time value.
After the prescaler value is selected, the dead time is
adjusted by loading a 6-bit unsigned value into the
DTCON1 SFR.
The dead-time unit prescaler is cleared on the following
events:
• On a load of the down timer due to a duty cycle
• On a write to the DTCON1 register.
• On any device Reset.
comparison edge event.
Note:
Dead-Time Generators
DEAD-TIME GENERATORS
DEAD-TIME RANGES
The user should not modify the DTCON1
values while the PWM module is operat-
ing (PTEN = 1). Unexpected results may
occur.
© 2011 Microchip Technology Inc.
CY
, 2 T
CY
Figure
, 4 T
CY
14-4, the
or 8 T
CY
)