TDA8566Q/N2C NXP Semiconductors, TDA8566Q/N2C Datasheet - Page 16

• Manufacturer Part Number: TDA8566Q/N2C
• Description: Audio Amplifiers 2X25W BTL STEREO RADIO PWR AMP
• Manufacturer: NXP Semiconductors

Specifications of TDA8566Q/N2C

• Product: Class-B
• Output Power: 55 W
• Available Set Gain: 26 dB
• Common Mode Rejection Ratio (min): 60 dB
• Thd Plus Noise: 0.05 %
• Operating Supply Voltage: 14.4 V
• Maximum Power Dissipation: 60000 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Audio Load Resistance: 4 Ohms
• Input Signal Type: Differential
• Minimum Operating Temperature: - 40 C
• Output Signal Type: Differential
• Supply Type: Single
• Supply Voltage (max): 18 V
• Supply Voltage (min): 6 V
• Output Type: 2-Channel Stereo
• Package / Case: DBS17P
• Operational Class: Class-B
• Audio Amplifier Output Configuration: 2-Channel Stereo
• Output Power (typ): 55x2@2OhmW
• Audio Amplifier Function: Speaker
• Total Harmonic Distortion: 0.05@4Ohm@1W%
• Single Supply Voltage (typ): 14.4V
• Dual Supply Voltage (typ): Not RequiredV
• Power Supply Requirement: Single
• Power Dissipation: 60W
• Rail/rail I/o Type: No
• Single Supply Voltage (min): 6V
• Single Supply Voltage (max): 18V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 17
• Package Type: DBS17P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: TDA8566Q/N2C,112

NXP Semiconductors
15. Soldering
TDA8566_6
Product data sheet
15.1 Introduction to soldering
15.2 Wave and reflow soldering
15.3 Wave soldering
This text provides a very brief insight into a complex technology. A more in-depth account
of soldering ICs can be found in Application Note AN10365 “Surface mount reflow
soldering description” .
Soldering is one of the most common methods through which packages are attached to
Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both
the mechanical and the electrical connection. There is no single soldering method that is
ideal for all IC packages. Wave soldering is often preferred when through-hole and
Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not
suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high
densities that come with increased miniaturization.
Wave soldering is a joining technology in which the joints are made by solder coming from
a standing wave of liquid solder. The wave soldering process is suitable for the following:
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless
packages which have solder lands underneath the body, cannot be wave soldered. Also,
leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,
due to an increased probability of bridging.
The reflow soldering process involves applying solder paste to a board, followed by
component placement and exposure to a temperature profile. Leaded packages,
packages with solder balls, and leadless packages are all reflow solderable.
Key characteristics in both wave and reflow soldering are:
Key characteristics in wave soldering are:
•
•
•
•
•
•
•
•
•
•
Through-hole components
Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Board specifications, including the board finish, solder masks and vias
Package footprints, including solder thieves and orientation
The moisture sensitivity level of the packages
Package placement
Inspection and repair
Lead-free soldering versus PbSn soldering
Process issues, such as application of adhesive and flux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are
exposed to the wave
Solder bath specifications, including temperature and impurities
Rev. 06 — 15 October 2007
2
40 W/2
stereo BTL car radio power amplifier
TDA8566
© NXP B.V. 2007. All rights reserved.
16 of 21